gmsn safety valve price

PLEASE NOTE: As with all vacuum tube based designs, this module is very sensitive to noisy power supplies. Check out this forum post for more info: https://forum.gmsn.co.uk/t/safety-valve-noise-problems/355

GMSN! Safety Valve Distortion - Eurorack synth module Look Mum No Computer LMNC. Fully assembled and tested GMSN!/Look Mum No Computer Safety Valve tube/valve distortion module, 11hp in Eurorack format. It"s nicely built and in excellent condition, fully tested and working, and only around a month old - it"s been used on one project only, in a smoke free studio. A unique and great sounding distortion with low current draw for a tube module, I"m selling only due to project completion and needing the space for something else. A module video can be found here: https://youtu.be/FHOXIhWkpss The GMSN panel and PCB (from which the module was built) details are here: https://gmsn.co.uk/products/look-mum-no-computer-safety-valve Power cable and mounting bolts are provided. A linear power supply is recommended (tried on a Doepfer PS2), as is placing the module away from potential sources of noise in your case, see the gmsn link for more details.

Of all the challenges you face keeping your customers’ plants operating at full capacity, safety and relief valves shouldn’t be one of them. NASVI’s job is to give you the confidence that your valve supply chain is rock solid regardless the pressure it’s under.

-It is designed for the 12ax7 tube to be soldered straight to the board without a socket to save excessive height. in this module provided you don’t chuck it off a balcony the valve will be fine, in this design it is also running cold so you wont have any worries of it prematurely breaking. It will last just as long if not longer than other components in the module.

-The valve also doesn’t even have to be soldered to function, if your feeling fancy look closely at the module in the above images you will notice i didn’t solder the valve in, the PCB actually holds onto the valve enough to provide sufficient contact, nearly as much as a socket would anyway! I am not sure how this will change over time, but for not it works fine. However if you want reliable and worry free use i would recommend to just solder it on down and forget about it.

-Touching the valve? This is a bit of a myth in respects to the fact that yes in some high temperature high reliability applications valves don’t want to be touched as over time the grease may indeed weaken the glass. But for general use and general purpose valves like the 12ax7 its completely negligible. in-fact this tube in this application doesn’t even get as hot as a cup of PG tips. So dont worry about it.

-Status LED! try to get a super bright 3mm LED, it will really make the tube illuminate as the heater filament in this application does not glow much if at all. In theory! a Bi Coloured LED would work too! Dont poke the LED all the way through the hole, just enough so that it is flush with the pcb, this means you can seat the valve right down to the PCB.

Surface-controlled subsurface safety valves (SCSSVs) are critical components of well completions, preventing uncontrolled flow in the case of catastrophic damage to wellhead equipment. Fail-safe closure must be certain to ensure proper security of the well. However, this is not the only function in which it must be reliable—the valve must remain open to produce the well. Schlumberger surface controlled subsurface safety valves exceed all ISO 10432 and API Spec 14A requirements for pressure integrity, leakage acceptance criteria, and slam closure.

Through decades of innovation and experience, Schlumberger safety valve flapper systems are proven robust and reliable. The multizone dynamic seal technology for hydraulic actuation of subsurface safety valves is a further improvement in reliability performance when compared with traditional seal systems in the industry.

The multizone seal technology is currently available in the GeoGuard high-performance deepwater safety valves, which is validated to API Spec 14A V1 and V1-H.

The RV10 safety relief valve is well-suited for overpressure protection of production equipment, including compressors, scrubbers, separators, pipelines or anywhere overpressure protection may be required.