off highway vehicle <a href=''>hydraulic</a> <a href=''>pump</a> monitoring for sale

The Power Team P-Series hand pumps come in a variety of configurations to meet the requirements of your application.  Along with various oil capacities and flow rates, you can choose from the following options:

Compact design ensures that the Power Team PA6 series pump is lightweight and portable. The PA6 series consists of single-speed pumps designed to drive single-acting cylinders. The power unit of choice for major manufacturers of auto body, frame straighteners and other equipment. Operates at 40-100 psi (3-8 bar) shop air pressure at the pump, dBA 85 at 10,000 psi (700 bar). Serviceable pump motor is not a “throwaway”, providing economical repair. Permanently vented reservoir cap. Internal relief valve protects circuit components, air inlet filter protects motor.

Compact, lightweight and portable the Power Team PA6D series pumps are single-speed pumps for driving double-acting cylinders. The PA6D series pumps operate at 40-100 psi (3-8 bar) shop air pressure at the pump. Designed with longevity in-mind the PA6D series feature internal relief valve protects circuit components, air inlet filter protects motor. Serviceable pump motor is not a “throw away”, providing economical repair. Permanently vented reservoir cap. dBA 85 at 10,000 psi (700 bar) for all PA6 pump.

Ideal for powering single-acting cylinders and portable hydraulic tools, the Power Team PA9 series pumps are easier to operate than a hand pump, designed for efficiency. Built to be economical in service; the PA9 series is not a “throwaway” unit. Unique bladder design for all-position operation and storage. Operates on 40-120 psi (3-8 bar) shop air, at 20 cfm (570 l). Hard-coat anodized aluminum housing. Oil filler with integral safety relief minimizes chance of damage to reservoir bladder if overfilling occurs.

A two-speed pump, the Power Team PA60 series pumps are designed for rapid oil delivery at low pressure to quickly advance cylinder or tool. Equipped with air pressure regulator, air filter and lubricator. Serviceable air motor for economical repair. Internal relief valve protects circuit components. Permanently vented reservoir cap.

Focused on single-speed and low pressure the Power Team PA50 series pump outputs 3,200 PSI / 220 BAR, fitting serviceable requirements for air motor for economical repair. Integrated air inlet filter protects motor. The PA50 series also features a filter in outlet port protects against contaminated systems Assorted reservoirs to suit your application"s requirements.

Rotary-Style Air Motor.  Use where air is the preferred source of energy.  3 hp motor starting under full load.  Two-speed operation for rapid cylinder advance.  Models available with full remote control over advance and return, except PA554.  Tandem center valve holds the load when pump is shut-off.

Compact, Portable, Cordless Hydraulic Pump for MRO Applications.  Compact, Li-ion 18VDC, 9.0 Ah battery-powered pump provides extended run-time.  Two-stage, high-pressure hydraulic pump offers quick tool advancement in the first stage.  Extremely compact, lightweight with an ergonomic handle grip and transport strap to ease portability.  Self-contained, rubber bladder reservoir allows pump usage in most positions with an impressive capacity of 70 cu. in. usable.  Quiet, smooth-running, serviceable brushed 18VDC motor.  High-impact, fiberglass reinforced shroud protects your investment in the most demanding and harsh applications.  Interchangeable valve configuration accommodates a vast array of applications.  CSA rated for intermittent duty, CE compliant.

The 10 series Power Team hydraulic pumps are designed to have a maximum of 690 bar (10,000 psi) at a flow rate of 164 cc/min (10 cu. in/min). All Power Team pumps come fully assembled, and each with the ability to be valved for either single- or double acting cylinders. Designed to be compact can easily mobile, the power team 10 series includes a portable power source is included for hydraulic cylinders, and tools. The permanent magnet motor is strategically constructed to easily start under load, even with reduced voltage conditions. Battery-operated models have 8 foot (2,4 m) power cord with alligator clips to connect to any 12 volt battery, optional rechargeable battery pack with shoulder strap are alternatives for maximum portability. The Power Team 10 series pump typically delivers 15 minutes of continuous operation at 10,000 psi (700 bar) on a single battery. Built to withstand High-impact, shielded with a flame retardant construction.

The Power Team 17 series pump is delibertly designed for maintenance and construction applications up to 55 Ton. For use with single-acting or double-acting cylinders at operating pressures to 10,000 psi (700 bar). For intermittent duty; starts under full load. Equipped with 1⁄2 hp (0,37 kW), 3,450 rpm, single-phase, thermal protected induction motor; 10 ft. remote control cord (PE172S has 25 ft. (7,6 m) cord) Low amperage draw; small generators and low amperage circuits can be used as power source. Extremely quiet noise level (67-81 dBA).

Vanguard Jr. + Power Team 18 series pumps provide two-speed high performance in a light-weight, compact package. Designed to provide a gauge port and metal reservoir on all pump models. Equipped with a 1⁄2 hp (0,37 kW), 115 volt, 60/50 Hz single phase motor that starts under load, even at reduced voltage. Low amperage draw permits use with smaller generators and low amperage circuits. All pumps have a 10 foot (3 m) remote control. CSA rated for intermittent duty. Noise level of 85-90 dBA. For operating hydraulic crimping, cutting or other tools: No. PE184C - Allows you to alternately operate a spring-return cutting and/or crimping tool without disconnecting either tool. Select a port connection with a manual 4-way valve, start the pump with a remote control hand switch and extend the connected tool. When the hand switch is switched to off, the pump stops and the automatic valve opens, allowing the tool to return. In the center (neutral) position, a manual control valve holds the tool in position at the time valve is shifted.

The 21 series Power Team pump and RD5513 cylinder used in a special press that produces pharmaceutical-grade extracts for herbal medicines. Totally enclosed, fan cooled induction motor: 1 hp (0,75 kW), 1,725 rpm, 60 Hz, single phase. Designed intentional for thermal overload protection. Remote control, with 10 foot (3,1 m) cord is standard on pumps with solenoid valves. Manual valve pumps have “Stop”, “Start” and “Run/Off/Pulse” switches. Pump controls are moisture and dust resistant. Motor drip cover with carrying handles and lifting lug. Low noise level of 70 dBA@ 10,000 psi (700 bar). In the event of electrical interruption, pump shuts off and will not start up until operator presses the pump start button. 24 volt control circuits on units with remote controls provide additional user/operator safety.

Ideal for running multiple tools or cylinders from one power unit. Recommended for cylinders up to 75 tons. Two-speed pumps have the same low pressure and high pressure flows from both valves. Flows and pressures of each pump are independent. Delivers 300 cu. in./min. of oil at 100 psi (4,8 liter/min of oil at 7 bar) and 25 cu. in./min. at 10,000 psi (0,4 liter/min at 700 bar) from each pump. 1 1/2 hp, 110/115 volt, 60 Hz (1,12 kW, 220 volt, 50 Hz) induction motor, 10 foot (3,1 meter) remote control and 5 gallon (19 liter) steel reservoir. Models available for operating single-acting or double-acting cylinders. Each power unit contains two separate pumps and two separate valves allowing operator to control multiple processes with one power unit. Both pumps on each power unit are equipped with an externally adjustable pressure relief valve. Not recommended for frequent starting and stopping.

The Power Team 30 series pump is intently ideal for maintenance and construction applications.  Operating both single-acting or double-acting cylinders. A dynamically built, Integral roll cage protects the 30 series pump from many forms of damage. 1 hp (0,75 kW), single phase, permanent magnet motor. High performance to weight ratio. Starts under full load even when voltage is reduced to 50% of nominal rating. Quit operations: 82 dBA @ 10,000 psi (700 bar) and 87 dBA @ 0 psi (0 bar). CSA rated for intermittent duty. Remote controls and/or solenoid valves feature 24 volt controls.

The Power Team 46 series is best suited for under the roof maintenance and production applications. Equipped with two-speed high-performance pump, for use with single- or double-acting cylinders at operating pressures to 10,000 psi (700 bar) the 46 series pump is versitile. With a 1 1⁄2 hp (1.12 kW), 3,450 (2,875) rpm single-phase, 60 (50) Hz thermal protected induction motor that starts under full load. Noise level of 77-81 dBA. All equipped with a 10 foot (3,1 m) remote control except PE462S which has a 25 foot (7,6 m) remote control. 24 volt control circuit on all units with remote control. CSA rated for intermittent duty.

A powerful multifaceted pump, the Power Team 55 pump excels at multiple applications. From heavy construction to concrete stressing this pump series is designed for intensity. With low voltage starting possible,  the 50/60 Hz universal motor; draws 25 amps at full load, and can start at reduced voltage. CSA rated for intermittent duty. 10 foot (3,1 m) remote motor control (except PE552S which has a 25 foot (7,6 m) remote motor and valve control). True unloading valve achieves greater pump efficiency, allowing higher flows at maximum pressure. Reservoirs available in sizes up to 10 gallons (38 liter). Lightweight and portable. Best weight-to-performance ratio of all Power Team pumps. “Assemble to Order” System: There are times when a custom pump is required. Power Team’s “Assemble to Order” system allows you to choose from a wide range of pre-engineered, off-the shelf components to build a customized pump to fit specific requirements. By selecting standard components you get a “customized” pump without “customized” prices. All pumps come fully assembled, add oil and ready for work.

A compact lightweight pump, the Power Team 60 series is designed for rugged applications and low voltage starting. Experiencing a long, trouble-free life in the most demanding work environments, the 60 series is durable.. Powered by 1 1⁄8 hp, 115 volt, 60/50 Hz (0,84 kW, 220 volt, 60/50 Hz) single phase motor. Starts under load, even at the reduced voltages at construction sites. Optional fan-driven external oil cooler includes rollover guard. Insulated carrying handle. Integral 4" (102 mm) diameter fluid-filled pressure gauge with steel bezel complies with ASME B40.1 Grade A. 0 to 10,000 psi (0 to 700 bar) pressure range in 100 psi (7 bar) increments. Sealed 3⁄4 gallon (4,34 liter (usable) reservoir. Reservoir drain port is standard. Standard oil level sight gauge for accurate oil level monitoring. External spin-on filter removes contaminants from circulating oil to maximize pump, valve and cylinder/tool life.

The Power Team PQ60 series pumps are designed specifically for heavy-duty, extended cycle operation. Integrating single- or double-acting cylinders the PQ60 series is versatile. Constructed for longevity by employing a metal shroud keeps dirt and moisture out of motor and electrical components. An electrical shut-down feature prevents unintentional restarting of motor following an electrical service interruption. Internal relief valve limits pressure to 10,000 psi (700 bar). External relief valve is adjustable from 1,000 to 10,000 psi (70 to 700 bar). The Power Team PQ60 pumps operate below maximum OSHA noise limitation (74-76 dBA). Start and operate under full load, even with voltage reduced by 10%.

The Power Team 120 series pump is exactingly designed for heavy duty, extended cycle operation up to 400 Ton. Built in grit, the series 120 pump can start and operate under full load, even with voltage reduced 10%. An electrical shut-down feature prevents unintentional restarting of motor following an electrical service interruption. Internal relief valve limits pressure to 10,000 psi (700 bar) and an external relief valve is adjustable from 1,000 to 10,000 psi (70 to 700 bar). Pump prewired at factory with a 3 hp, 460 volt, 60 Hz (2,24 kW, 380 volt, 50 Hz), 3 Phase motor. Other electrical configurations are available. 24 volt control circuits on units with remote controls for added user/operator safety. 3 hp (2,24 kW) 3 phase motor with thermal overload protection. Motor starter and heater element supplied as standard equipment; with an intentionally designed metal shroud to keep dirt and moisture out of motor and electrical components. Pumps operate below maximum OSHA noise limitation.

With high tonnage double-acting cylinders, the Power Team 400 series offers both single or multiple cylinder applications. Two-speed high output pump delivers up to 5 gpm (16 liter/min) of oil, with a low noise level of 73-80 dBA. Integral electrical shut-down feature prevents unintentional restarting of motor following an electrical service interruption. Over-current protection prevents damage to motor as a result of overheating. “Stop” and “Start” control buttons are 24 volt. PE4004 has a 4-way/3-position manual valve. The PE4004S has a 4- way/3-position solenoid valve with a 24 volt remote hand switch. External pressure relief valve is adjustable from 1,500 to 10,000 psi (100 to 700 bar). Heavy duty 4" (50,8 mm) diameter casters assure easy maneuvering. 20 gallon (3,927 cu. in. usable) / 75,7 liter (62,8 liter usable) reservoir has a low oil level sight gauge. Powered by a dual voltage 10 hp (7,46 kW), 3 phase, 1,725 (1,437) rpm motor. 3 phase motor has all the electrical components necessary to operate the pump.The customer has no hidden charges when making purchase. Deliver 1,200 cu. in./min. (16 liter/min) of oil @ 200 psi (15 bar), 420 cu. in./min. (5,6 liter/min) of oil @ 10,000 psi (700 bar).

Power team synchronized lifting and lowering system, the MCS ( motion controller system ) series can be used in many hydraulic applications where load position is critical, requiring cylinder synchronization. Whether it is a bridge, a building or any kind of heavy load, with the SPX FLOW power team motion control system, lifting, lowering, pushing, pulling, tilting or positioning loads can be carried out automatically with a high degree of accuracy. The PLC-controlled system is a combination of digital actuation and digital control providing significant advantages such as time savings, repeatability, and extremely low internal stress in the object one is moving. The system also provides documentation for the movement performed.

Extremely durable yet lightweight and operable under low-line voltage conditions, the Power Team PE-NUT series pumps are constructed for challenging conditions. A 115V 5/8 hp (0,46 kW) universal electric motor (50/60 cycle), employing a two-stage pump for efficiency and designed for use with spring-returned remote tools. The PE-NUT series pumps also feature high-pressure safety relief valve, remote hand control with 10-foot (3,1 meter) cord, and a pressure matched quick-coupler supplied. The PE-NUT series uniquely utilizes intermittent duty, piston-type high-pressure pump supercharged by a low-pressure pump. CAUTION: DESIGNED FOR CRIMPING APPLICATION ONLY! This system should not be used for lifting.

Gasoline power ideal for remote locations.  A logical choice at work sites where electricity or compressed air are unavailable. For single or double-acting cylinders at operating pressures up to 10,000 psi.  All gasoline engine/hydraulic pumps feature Posi-Check® valve to guard against pressure loss when valve is shifted from “advance” to “hold.”

PG303 is for single-acting cylinders, has a 9520 valve with separate internal return line which allows oil from running pump to return to reservoir, independently of cylinder return oil, when valve is in “return” position.

PG1200 Series pumps powered by a Honda 4-cycle, 5.5 hp engine with automatic decompression and electronic ignition. Deliver over 0.5 gallon (130 cu. in.) of oil per minute at 10,000 psi.

Rubber anti-skid insulation on bottom of reservoir resists skidding and dampens vibration. PG1200M-4 and PG1200M-4D include a pump cart with 12” wheels.

The Power Team HB series is purposefully constructed to convert low-pressure portable hydraulic pumps or on-board hydraulic systems, into high pressure power sources. HB series applications include utilities, railroads, construction, riggers and others. This product operates single or double-acting cylinders, jacks, and tools such as crimpers, spreaders, cable cutters, or tire tools. Version for use with double-acting torque wrenches available. May be used to operate two separate, single-acting tools (with integral valves) independently, without need for additional manifold. Control valve included. Other Power Team valves available as an option to suit your specific application, if needed; consult factory. Compact and rugged for use inside a utility vehicle aerial bucket or stowing in a vehicle. No reservoir level to maintain; uses low pressure system as oil supply. Has 3⁄8" NPTF ports; compatible with standard fittings for low and high pressure systems.

Portable two-speed pump operated in any position (open or closed-center) providing pressures up to 10,000 psi for the operation of high-pressure tools.

These compact, lightweight boosters do not have reservoirs. The units can be operated in any position on either open- or closed-center (accumulator) hydraulic systems.

“Assemble to Order” means you can choose a basic pump with gas, air or electric motor. Then select the proper valve, gauge, pressure control, motor control and reservoir. You get a two-stage pump that gives high oil volume for fast cylinder approach (and return with double-acting cylinders) in the first stage and high pressure in the second stage.

3 HP Jet Motor, Three-Phase.  Gives low noise level and long life due to its moderate operating speed. Ideal for fixed installations. Consists of basic 10,000 psi pump, jet pump motor: 3 hp, 3,450 rpm, 230/460VAC, 60 or 50 cycle (specify). AC three-phase, with thermal overload switch. Equipped with internal and external relief valve. Will start under load.

or cannot be used. The 5,000 or 10,000 psi pump has a 3 hp air-driven motor at 3,000 rpm (optimum performance based on 80 psi air pressure and 50 cfm at the pump). You can drive single or double-acting cylinders with the correct valve.  NOTE: 80 psi air supply required to start under full load.

unavailable. It is capable of continuous operation at full pressure. Consists of basic 10,000 psi pump, 4-cycle Briggs & Stratton “Diamond Edge” gasoline engine, developing 6 hp. As with all these pumps, this unit can be valved for use with either single or double-acting cylinders.

off highway vehicle <a href=''>hydraulic</a> <a href=''>pump</a> monitoring for sale

With Linde Hydraulics discontinuing their in-house remanufacturing program in February of 2023 - Hydraulex (our Washington State facility) is now 1 of 5 Authorized Linde Service Centers within the USA and Canada. We"ve worked closely with Linde for many years and have factory training & are factory supported by Linde.

off highway vehicle <a href=''>hydraulic</a> <a href=''>pump</a> monitoring for sale

Barndoor Ag is proud to now offer Ace pumping solutions for the chemical application, off-highway equipment, air conditioning, and refrigeration markets.

Ace has developed a complete range of products for the agricultural and off-highway equipment markets that do not require the electrical grid for operation. Ace pumps are found serving a variety of functions in industry today including: crop sprayers, concrete trucks, asphalt milling machines, anti-icing trucks, turf sprayers, and more. Shop for agricultural pumps and save!

off highway vehicle <a href=''>hydraulic</a> <a href=''>pump</a> monitoring for sale

With features that maximize electrical efficiency and minimize water consumption, and options for remote monitoring of pressure, temperature and fluid level, these HPUs will help reduce facility energy costs. For additional energy savings, the larger units can be equipped with a run-on-demand option that reduces electrical power and cooling water consumption when the system is not running at full capacity.

off highway vehicle <a href=''>hydraulic</a> <a href=''>pump</a> monitoring for sale

A large touchscreen display allows monitoring of overall fluid demand, control fluid supply and balance the load to distribute hydraulic fluid power only when and where it is needed. This ability to control up to 8 HPUs as a single system helps improve productivity, reduce energy costs and prolong equipment life.

off highway vehicle <a href=''>hydraulic</a> <a href=''>pump</a> monitoring for sale

Dedicated to customer service, we understand you have unique needs with tight timelines. We work hard to deliver what you need, when you need it. Our 15 locations across the United States warehouse a large inventory of hydraulic cylinders, motors, pumps, hose ends, & more.

off highway vehicle <a href=''>hydraulic</a> <a href=''>pump</a> monitoring for sale

The mobile machinery sector includes all components and solutions to create non-road vehicles, heavy machinery, self-propelled, towed or pulled machines, primarily for use in the construction and maintenance of roads, bridges, trenches, buildings and land reclamation.

Performance - Speed - Accuracy - Capacity - Long Life Reliability - Robustness - Ease of Use are all well known features for Hydreco Hydraulics pumps and motors even in the harshest of environments.

Responsiveness, Accuracy, Reliability and Robustness are all design features of the range of Hydreco Hydraulic valves which will continue to perform as specified in the most challenging arenas.

The Hydreco Group offers a range of products for agricultural machinery composed of hydraulic cylinders, gear pumps, control valves, joysticks and machine control systems, offering customers the optio...

From the upstream side of on-shore and off-shore extraction facilities, through to midstream applications in process valves and compressors, and finally downstream in refineries, Duplomatic supports t...

The Hydreco Group offers a comprehensive range for the construction of machines used for forestry: gear pumps, control valves, joysticks and machines control systems.

The Hydreco Group is specialized in components for vehicles in the transport sector. The requirements to be guaranteed for this type of vehicle are very specific and highly important.

off highway vehicle <a href=''>hydraulic</a> <a href=''>pump</a> monitoring for sale

Positive displacement pumps are used in agricultural applications to produce high fluid pressure.  Applications include injection of a chemical into a pressurized irrigation pipe system, along with fluid transfers in sprayers and chemical metering.

Gear pumps can be either internal or external styles, depending on the position of the gears. The external type being the most popular type used today in modern hydraulic systems.

For larger machinery with continuous running hydraulic functions along with the need for steering actions, a variable displacement piston pump is a standard choice. A pressure-compensated and load-sensing piston pump provide a flow that automatically matches the demands of the cylinder and hydraulic motor flow demand.

The hydraulic functions on agricultural equipment can be easy-to-operate with GS Global Resources integrated system solutions.  Such as our touchscreen programming of timed hydraulic function, fingertip switches all providing the operator HMI with convenient easy-to-use automation options, along with our wide selection of pumps and motors including our line ofBondioli & Pavesi Gear Pumps, solidly constructed and among the most widely utilized in the field of hydraulics.

off highway vehicle <a href=''>hydraulic</a> <a href=''>pump</a> monitoring for sale

Kawasaki’s new medium duty pump, the K3VLS, has been developed for machines and equipment that use a load sensing control system and/or electric displacement control systems. Its launch follows extensive research and development as our engineers combined efficiency with simplicity to deliver the most technologically advanced pump on the market.

off highway vehicle <a href=''>hydraulic</a> <a href=''>pump</a> monitoring for sale

This is the ATV attachment you’ve been looking for! This original component of the Wild Hare ATV Implement System opens up new opportunities, increases efficiency, and puts the control in your hands. The simple handlebar-mounted rocker switch controls lift and lowers up to 500 lbs. The heart of the system is our hydraulic power pump that operates off of a 12-volt deep cycle battery. Because of the hydraulics, it easily lifts or creates down pressure for back dragging, scraping, and digging. Since we don’t use the winch or a trip bucket you don’t have to get off your machine to reset the trip on the bucket. It also lifts approximately 3 times higher than a winch style bucket! The hydraulics are so powerful, they can actually lift your ATV off the ground! Our 4 wheeler bucket makes it easy to load anything into the back of your pickup or pile snow high. Whatever your need, our ATV hydraulic loader will deliver.

off highway vehicle <a href=''>hydraulic</a> <a href=''>pump</a> monitoring for sale

HT transmissions reduce the number of parts on a zero turn mower propulsion system from 72 to 2 parts requiring less installation and procurement labor, which provides increased customer efficiency. Parker"s Integrated HTE Hydrostatic Transmissions provide a compact, economical solution for the propulsion systems of off-highway vehicles up to 1300 lb. gross vehicle weight. One integrated package contains the hydrostatic variable displacement pump, reservoir, filter and standard of the industry low speed, high torque motor eliminating dozens of additional parts, reducing associated inventory and labor costs. Parker"s Integrated Hydrostatic Transmissions perform with up to 10% more overall efficiency than competitive offerings. This means more horsepower is available to the mowing deck or other functions, and more hill-climbing capability.

The HTE Series transmission is a compact integrated product featuring torques to 5180 lb-in, side load to 2000 lb., shaft size 1.25 inch, integrated Parker axial piston pump and motor assembly, integral charge pump, world famous Parker Torqmotor™ TE gerotor motor, built-in internal fluid reservoir and filter, direct porting between the pump and motor, no external reservoir needed, fluid filled for life, with fan and pulley included. Options: integral parking brake, four or five bolt hub, return-to-neutral assist and integral shock relief valves.

off highway vehicle <a href=''>hydraulic</a> <a href=''>pump</a> monitoring for sale

When used as part of a vehicle’s control or predictive maintenance system, the use of one or more Webtec CTA flow monitors/meters can achieve next-level productivity improvements. This is largely because predictive maintenance ensures engineers can make arrangements to replace a component before it reaches the end of its useful life without enduring an extremely costly, disruptive and potentially dangerous catastrophic failure.

The CTA flow meter’s principle of operation is a proven design that uses a turbine wheel mounted in the flow stream and a sensor which senses the passing of each turbine blade. The on-board electronics then convert the sensor pulses into a flow-rate signal ready for transmission via an SAE J1939 CAN-bus signal to the vehicle’s control system. Indeed, the vehicle’s control system could also serve as a link to centralised monitoring and diagnostic station. As a point of note, the CAN-bus connection is facilitated by a Deutsch automotive connector in-line with inlet port to reduce height.

Of course, there are many possible applications for a permanently installed flow monitor capable of linking to a vehicle’s cloud-based communication system. For instance, such an investment can provide an accurate prediction of when system or component maintenance is required on earthmoving, mining and municipal vehicles, as well as cranes and especially autonomous vehicles. In these use cases, the flow monitor can continuously assess pump performance. When using variable displacement pumps, it is possible to incorporate regular test routines into the vehicle’s operation so that monitoring takes place under consistent and known operating conditions.

The CTA flow monitor can also facilitate system performance information and action in safety-critical applications, like tilting trains or hoists. Monitoring the outlet flow from a winch drive motor, for example, will give an immediate indication of potential over-speed. In addition, Webtec’s CTA flow meter can form part of an actuator’s open- or closed-loop control system. Here, users can obtain a feedback signal proportional to the actuator speed by monitoring the actuator flow rate, which they can then use for the closed-loop speed control of the actuator.

off highway vehicle <a href=''>hydraulic</a> <a href=''>pump</a> monitoring for sale

For hydraulic systems that place high demands on control engineering, servo pumps are the perfect solution. The basic version of these pump systems also consists of three main components:Servo inverter

Servo pumps control the pressure or the volume flow. They precisely convert electrical energy into the hydraulic energy that is currently needed in the system. The classic use of valves for control can be either completely or partially omitted. This considerably simplifies every hydraulic system.