pto hydraulic pump gearbox pricelist

Brand new cast iron made P.T.O gearbox is ideal for adding hydraulic power to tractors and landscape equipment not already equipped with hydraulic circuits, or in need of auxiliary hydraulics. Used to power hydraulic Auger, front-end loaders, mowers, rotary sweepers, etc. These gearboxes are used mainly for connecting hydraulic pumps to the power take-offs of agricultural tractors. It is powerful enough to transfer the load of 100 LPM @ 2850 psi. Please note the last photo is of the gearbox fitted with a Vivoil Group 3 pump. This pump is not included in this sale, it is purely to show how this looks once you mount a pump.

These PTO speed increases can be used with either a Group 2 DIN mount pump, or a Group 3 DIN mount pump. See other listings for a PTO Speed increaser complete with a pump. This listing is just the speed increase box with a pump shaft spline adapter. If you supply your own pump, it needs to be CW, clockwise rotation.

If running your PTO at ; 540 RPM x 3 = 1620 RPM . Then multiply the pump CCs. ie. 39cc x 1620 = 63180ccm / 1000 = 63LPM Please allow for approx 20% pump inefficiency, so if after 60LPM, go up to 43cc pump, 1620 x 43 =69LPM less 20% = 56 PM

The standardized PTO output of 540 Rpm is, in this way, increased x 3:1 to optimum operating speeds for the hydraulic pumps. This gearbox and pump offer either direct or remote mounting options to the tractor P.T.O to provide independent hydraulic service. This gearbox itself is rated to provide up to 37 KW or 50 HP to the hydraulic gear pump. This figure is nothing to do with your engine horsepower, only the power the gearbox is able to transfer to the hydraulic pump(see chart below) Female or Male shafts are the same prices.

This comes with standard Female 1-3/8" 6 splined shafts generic to most PTO output shafts. This step-up gearbox has a ratio of 3:1 which means, if your PTO is spinning at 540 RPM, it will step up the speed to 1620 RPM.

The main considerations in choosing the correct size pump for your application; are the amount of Flow required & the pressure required. As the need for higher pressure (PSI) is increased, the power required to produce this pressure rises. It is easy to pump fluid at a high flow rate if low psi is required, but it takes a lot of HP to pump high flow rates at a high PSI.

This Brand new Italian-made P.T.O gearbox and pump assembly are ideal for adding power to tractors and landscape equipment not already equipped with hydraulic circuits. Used to power hydraulic Auger, front-end loaders, mowers, rotary sweepers, etc.

These aluminium gearbox housings and hardened steel internal gears are used mainly for connecting hydraulic pumps to the power take-offs of agricultural tractors.

The standardised PTO output of either 540 or 1,000 rpm, is, in this way, increased to optimum operating speeds for the hydraulic pumps. This gearbox and pump offer either direct or remote mounting options to the tractor P.T.O to provide independent hydraulic service.

This comes with standard Female 1-3/8" 6 splined shafts generic to most PTO output shafts.(photos) If your shaft has " grooves", there is an Optional Shaft "Quick release" coupler available for an extra $40. Also available at no extra cost is a Male shaft. There is the option of a few other couplers so feel free to ask or send photos for confirmation.

There are a variety of pump sizes to choose from, please see the drop box next to the photos. All are the same price. The main considerations in choosing the correct size pump for your application are the amount of Oil Flow and the pressure required.

As the need for higher pressure (PSI) is increased, the power required to produce this pressure also rises. It is easy to pump fluid at a high flow rate if low psi is required, but it takes a lot of HP to pump high flow rates at high PSI pressures.

Please refer to our chart below, & feel free to message or call with any queries. We also supply reusable field fit hydraulic hose fittings hose and & any hydraulic valves or adaptors you require.

40 Lpm @ 1800 psi is the most flow, the pressure this size gearbox can reliably sustain. Warranty is void if run at over 1800Psi with a pump larger than 20cc. If more flow is required, please check our next size-up gearbox

PLEASE NOTE BELOW All Hydraulic pumps typically have a 20% efficiency loss factor. The numbers supplied below are gross figures, please take 20% for the correct PM

We carry many types of adaptors, threads, hydraulic hose, and field fit hose fittings available please see our other listings or contact us for great prices & service.

Explore a wide variety of pto gearbox pump on Alibaba.com and enjoy exquisite deals. The machines help maintain drilling mud circulation throughout the project. There are many models and brands available, each with outstanding value. These pto gearbox pump are efficient, durable, and completely waterproof. They are designed to lift water and mud with efficiency without using much energy or taking a lot of space.

The primary advantage of these pto gearbox pump is that they can raise water from greater depths. With the fast-changing technology, purchase machines that come with the best technology for optimum results. They should be well adapted to the overall configuration of the installation to perform various operations. Hence, quality products are needed for more efficiency and enjoyment of the machines" full life expectancy.

Alibaba.com offers a wide selection of products with innovative features. The products are designed for a wide range of flow rates that differ by brand. They provide cost-effective options catering to different consumer needs. When choosing the right pto gearbox pump for the drilling project, consider factors such as size, shape, and machine cost. More powerful tools are needed when dealing with large projects such as agriculture or irrigation.

Alibaba.com provides a wide range of pto gearbox pump to suit different tastes and budgets. The site has a large assortment of products from major suppliers on the market. The products are made of durable materials to avoid corrosion and premature wear during operations. The range of products and brands on the site assures quality and good value for money.

Selecting the best transmission will mostly depend on the usage of the vehicle. Alibaba.com has a massive collection of truck transmission and wholesale pto pump gearbox for all budgets. Knowing the application of a truck is the first step to choosing the transmission and engine. 10 speed shifting transmissions are among the most widelly used transmission system for or off-road and on-road tracks. Factors that determine the transmission selection inlude; the maximum grade, road condition, and the GCVW .

Semi truck automatic transmission is needed for a smooth ride and ensures that the seat doesn"t vibrate. With a good transmission system, a truck handling will improve and the drive will feel more confident maneuvering a truck while carrying a load. Truck automatic transmission is for the shoppers who want a pto pump gearbox. This helps the drive achieve a comfortable hassle-free journey, that keeps them away from thinking about shifting. Among some available transmissions, Eaton Fuller 10 Speed Transmission and Ram 3500 Transmissions are notable that work perfectly for heavy-duty trucks.

The PTO gearbox and pump assemblies are ideas for adding power to tractor or landscape equipment not already equipped with hydraulic circuits. Use to power hydraulic motors front end loaders, mowers, and rotary sweepers. The gearbox and pump range offer either direct or remote mounting options to the tractor PTO to provide independent hydraulic service.

The Pump kit is consists of an aluminum-alloy housing and a high-strength hydraulic PTO gear pump. With bearable steel gears and shafts, it has an extending product life cycle, more sturdy and durable.

The spline type shaft runs coordinately with the hydraulic gear pump, rotated in clockwise. Gear Ratio: 1: 3.8. The whole PTO pump set can work under the condition that the Max pressure is 250bar / 3500psi.

The PTO gear pump with its speed up to 540rpm, with its power in 20kw and runs in a low noise condition. There are two oil ports for oil inlet and outlet respectively, fast and convenient, capable of quick oil output.

This tractor PTO pump with an excellent performance in pumping out oil with its displacement of 25 cc/rev, 53 liters per minute. No worries about oil trapping or leaking.

The whole set PTO gearbox hydraulic pump includes a clockwise gearbox with a long tube sleeve, and inside gear pump. A free seal ring helps to ensure no oil leakage.

With excellent performance and high efficiency, it is widely used in many industries such as agricultural, garden, and transportation, to power hydraulic motors front end loaders, mowers, and rotary sweepers.

Variable displacement axial piston pumps. These pumps are the optimal solution for mobile applications. Available with a wide range of control options. Compact design makes them ideally suited for direct mount to engines and gearboxes. The displacements in each frame size are infinitely variable between maximum and minimum via simple screw adjustment. The pump shaft supports full torque transmission in multiple unit configurations. They are available in side (L) and rear (P) ported versions. Addition versions available, please contact your nearest Southcott branch or distributor for the availability of the unit to suit your requirements.

This brand new Italian-made P.T.O (Power Take Of) comprises a 3:1 speed increase Gearbox and Hydraulic Gear Pump. It is ideal for adding Hydraulic power to tractors and landscape equipment that are not already equipped with hydraulic circuits.

Used to power hydraulic Auger, front-end loaders, mowers, rotary sweepers, Post Hole Borers, and Post Drivers. These gearboxes are used mainly for connecting to the power output shaft at the rear of the tractor to drive hydraulic pumps to generate fluid power.

The standardized tractor PTO output of either 540 (turns into 1620 Rpm) or 1,000 rpm, is, in this way, increased to optimum operating speeds for the hydraulic pumps.

This gearbox and pump offer either direct or remote mounting options to the tractor P.T.O to provide independent hydraulic service. This gearbox is rated to provide up to 20 KW or 27 HP to the hydraulic gear pump. This figure is nothing to do with your engine horsepower

This comes with standard Female 1-3/8" 6 splined shafts generic to most PTO output shafts. (photos) If your shaft has " grooves", there is an Optional Shaft "Quick release" coupler available for an extra $40.

Please see the last photo which shows the "groove" in the PTO shaft which fits the "Quick" release. Also available at no extra cost is a Male shaft. There is the option of a few other couplers so feel free to ask or send photos for confirmation

This step-up gearbox has a ratio of 3:1 which means, if your PTO is spinning at 540 RPM, it will step up the speed to 1620 RPM. There are a variety of pump sizes to choose from, please see the options next to the photos. All are the same price.|The main considerations in choosing the correct size pump for your application, is the amount of flow required & the pressure required. As the need for higher pressure (PSI) is increased, the power required to produce this pressure rises.

It is easy to pump fluid at a high flow rate if low psi pressure is required, but it takes a lot of HP to pump high flow rates at a high PSI. Please refer to our chart below, & feel free to message or call with any queries.

Please take careful note of the flow & pressures in the chart below. This unit is rated for up to 10Kw hydraulic power only. If you require more flow & higher PSI, please see our other size gearboxes/pumps in the agricultural category of our store.

Hydraulic transmissions are used for speed and torque conversion. They are particulary suitable for driving powerful machines - because the pump and the hydraulic motor are physically separated and can be mounted separately at a suitable location. Among the most common applications of hydraulic transmissions are electronically controlled systems that require controlled working speed at full engine power.

Prince Gear Pumps are manufactured by Prince Manufacturing Corporation, who pride themselves in being a premier manufacturer of high-quality hydraulic pumps.  Their engineering expertise, state-of-the-art manufacturing equipment and strong employee work ethic attribute to the long-life and durability of their products. Beiler Hydraulics has many configurations of Prince pumps in stock but if you are searching for a pump you don"t see on our website please contact us and we will be glad to check our inventory or special order the pump you need.

These are designed for high HP Tractors to lower the rpm of the tractor engine. We carry curved jaw couplers in metric sizes. If you need metric on one side and inch sizes on the other for running water pumps or fans, or other equipment that require inch size, We can help you get the proper LoveJoy coupler.

PRINCE PTO HYDRAULIC PUMPS Up to 40 gallons per minute and up to 2250 psi UNIQUE FEATURES: PLUS STANDARD FEATURES: • Self-adjusting wear plates on both sides of the gears. • Proper size hose adapters are provided for inlet ports. • Two outlet ports are provided with a NPT adapter for one port and a plug to seal unused port. • Center section available in high strength aluminum alloy for std. duty cycle or in high strength cast iron for high duty cycle use. • Tractor front end loaders • Pull-type cotton pickers • Cotton balers (module builders) • Reliable • Efficient • Roller Bearings • Run fitted body • Internally splined drive shaft. • High-tensile cast iron end plates. • Slips onto tractor PTO shaft (no gear box required). • Two-bolt installation on farm tractors of all sizes. • Tractors imported without integral hydraulics • Landscape equipment • Rotary mowers • Street Sweepers • Back hoes MODEL FEATURES ALUMINUM CENTER HOUSING • Standard duty cycle • Reduced weight • Smaller housing CAST IRON CENTER HOUSING • High duty cycle • Use in circuits with motors • Better at higher temperatures • Increased wear resistance REAR PORTED • Higher flows • Simplified hose connections • Higher flows at reduced engine rpm as compared to other PTO pumps Prince PTO pumps are specifically designed for PTO drive operation on all sizes of farm tractors. No additional gear box is required. Pumps are mounted by sliding the internally splined pump onto the PTO splined shaft and restraining rotation with a torque arm. See page P6 for the PTO pump torque arm kit. • FILTRATION The pump must be used in a clean system with clean oil. The fluid cleanliness should meet the ISO 4406 17/14 level. As a minimum, 10 micron filtration is recommended. • HYDRAULIC FLUID A good quality mineral base hydraulic fluid with a viscosity in the 70-250 SUS range at operating temperature is recommended. • OPERATING TEMPERATURE Oil operating temperature should not exceed 180°F. If it does, the reservoir may be too small or a heat exchanger may be needed. • SHAFT SPEEDS Prince PTO pumps are designed to operate at up to 110% of standard PTO shaft speeds. Standard speeds are 540 rpm for the 6 tooth shaft and 1000 rpm for the 21 tooth shaft. CATP 3-01-20-01 • CLOSE RUNNING CLEARANCE FOR HIGH FLOW RATE Another feature that contributes to the excellent and long-lived efficiency of the PTO-Series pump is the minimum clearance between the gears and the center housing. Each pump is assembled with zero clearance between the housing and the tips of the gear teeth, then test run until the teeth establish a proper wear path in the housing. The result is a much tighter clearance than found in traditional pumps. • PRESSURE RATING Pumps are designed for 2250 PSI max. relief valve setting. A relief valve, external to the pump, must be provided in the system. • PORTS All pumps are provided with an inlet port adapter (SAE O-ring boss to hose barb) and outlet port adapter (SAE O-ring boss to female pipe thread) sized appropriately for the ports and required line sizes. A steel plug is provided for the second outlet port. • RESERVOIR As a guideline, a reservoir size in gallons should equal the pump output in gallons per minute. A larger reservoir and/or an oil cooler may be needed for high duty cycle applications. PRINCE MANUFACTURING CORPORATION/WORLD HEADQUARTERS • NORTH SIOUX CITY, SOUTH DAKOTA 57049 URL: www.princehyd.com • E-MAIL: prince@princehyd.com O.E.M. CUSTOMER SERVICE: (605) 235-1220 • FAX (712) 233-2181 DISTRIBUTOR CUSTOMER SERVICE: PHONE (605) 235-1220 • FAX (712) 233-2181 • SELF ADJUSTING WEAR PLATES Prince PTO pumps have self-adjusting wear plates that seal around the two unequal size gears. T