remote mount hydraulic pump manufacturer

Genuine Metaris Dump Pumps are known for their ruggedness, reliability and interchangeability. Available in both the 101 Remote Mount and the 102 Direct Mount configurations and C or G frames, these pumps offer cast iron construction, a variety of displacements and “Air Shift” capabilities.

The Remote Mount Hydraulic Dump Pump with Manual Valve from Buyers Products is a compact and efficient source of hydraulic power for your vehicle. It is designed for dump operations with 2 or 3 line plumbing and has cable-controlled shift operations. The pump is controlled with an easy on/off switch in your truck cab. Based on RPM, its output ranges from 13 to 46 GPM. It includes a relief valve set at 2500 PSI. The pump/valve is remote-mounted. The pump bracket is sold separately.

The Remote Mount Hydraulic Dump Pump with Air Control from Buyers Products is a compact and efficient source of hydraulic power for your vehicle. It is designed for dump operations with 2 or 3 line plumbing and has pneumatically-controlled shift operations. The air shift cylinder is included. The bracket is sold separately.

• The Economy pump is best suited to power small to medium size fixtures. Its lightweight and compact design makes it ideal for applications which require easy transport of the pump. ...

... start the pump with a remote control hand switch and extend the connected tool. When the hand switch is switched to off, the pump stops and the automatic valve opens, ...

... with 1⁄2 hp (0,37 kW), 3,450 rpm, single-phase, thermal protected induction motor; 10 ft. remote control cord (PE172S has 25 ft. (7,6 m) cord) Low amperage draw; small generators and ...

... voltage. CSA rated for intermittent duty. 10 foot (3,1 m) remote motor control (except PE552S which has a 25 foot (7,6 m) remote motor and valve control). True unloading ...

... 1000bar. The HP-REMOTE pump, like all the HP Series pumps, can be installed in any hydraulic applications which requires high working pressures and moderate and controllable ...

Compact and sturdy construction for heavy duty and long durability over time, The UPRD-SE710 single acting air hydraulic pump has a double air motor, a pneumatic RC drive and a 3-button ...

The Buyers Products hydraulic dump pump is designed as a compact and efficient source of hydraulic power for your vehicle. It is primarily used for dump operations with 2 or 3-line plumbing.

Buyers HydraStar™ Remote Mount Hydraulic Dump Pump with Manual Valve from Buyers Products is a compact and efficient source of hydraulic power for your vehicle. It is designed for dump operations with 2 or 3 line plumbing and has cable-controlled shift operations. The pump is controlled with an easy on/off switch in your truck cab. Based on RPM, its output ranges from 13 to 46 GPM. It includes a relief valve set at 2500 PSI. The pump bracket is sold separately.

Dump Pumps are not recommended for ejector, conveyor, or moving floor type applications; please refer to Gemini brochure for those type or applications

Powering a hydraulic pump to a power take-off (PTO) is a common practice. Within mobile hydraulic applications, there are three types of hydraulic pump construction typically found including gear, piston and vane.

Gear pumps are the most common design used in truck mounted hydraulic systems, as the gear pump is relatively inexpensive with its fewer moving parts, ability to be easily serviced and greater tolerance to contamination than other designs.

A hydraulic pump for mobile applications, like the gear, piston or vane pump, can be either direct mounted to the PTO or remote mounted – using a driveline. While each type is a viable option for mounting a hydraulic pump, it is important to understand each type of mount to ensure an effective connection is made between the PTO and pump.

In a direct mount the hydraulic pump is mounted directly to the output flange of the PTO. Direct mounting is the most common type of installation in the mobile equipment industry. When direct mounting a pump it is necessary to:

Select the correct pump rotation to match the PTO output rotation or select what is known as a bi-rotational pump, which tends to have equally sized ports since either can be the inlet or outlet.

For mobile, truck mounted hydraulic systems the most common pump mount is the SAE B, which is a 7/8” diameter shaft with 13 splines – one of the standard pump mounting configurations established by the Society of Automotive Engineers (SAE).

Disadvantages to direct mounting a pump• Concealed maintenance points, which include periodic removal and replacement of grease at the pump to PTO connection

Sometimes it is not possible to direct mount a hydraulic pump, requiring the pump to be remote mounted some distance away from the PTO and then powered from the power take-off by means of a driveline assembly. The correct type and series of driveline must be selected. Solid shafting is not recommended as it cannot be balanced and can vibrate, damaging the PTO and pump shaft seals – causing leaks. The better choice is a balanced, tubular assembly designed to meet the speed, torque and horsepower requirements of the application.

When using a driveline, it is important that it be in phase and incorporates a slip yoke at one end. Round, keyed PTO output shafts are susceptible to failure by high cyclic loading. An out of phase shaft will vibrate and damage the PTO and pump shaft seals while a functioning slip yoke will allow the shaft to adjust for flexing of the truck chassis. As part of a regularly scheduled, preventative maintenance plan, the slip yoke and bearings of the driveline must be lubricated.

Powering a pump to a PTO is a common practice, but selecting whether to direct or remote mount the pump takes understanding and careful consideration. Regardless of the type of mount you select, remember that this understanding of each mount – along with its advantages and its drawbacks – will be the key to creating an effective, lasting connection between the PTO and pump.