seastar hydraulic pump free sample

The world"s most popular hydraulic boat steering helm (HH52713) offers smooth, efficient no feedback steering for inboard and outboard applications. Super-efficient steering for today’s high performance hulls with single or multiple outboards up to 700 HP combined. It’s the OEM Choice for center consoles, cruisers and more.

No boat is going to run smoothly 100% of the time. There are always going to be problems that crop up or issues that need to be addressed and fixed before they cause lasting damage to your boat. That’s why it’s helpful to know what mechanical issues to expect and how to solve them yourself. So let’s take a look at some of the most common SeaStar hydraulic steering problems and what to do when you encounter them.

For example, keeping your reservoir topped up withSeaStar Hydraulic Steering Fluidwill usually keep it from running too low, but if the real problem is a leaking seal, you’re going to end up with more problems than just low fluid.

We’ve put together a handyDIY training videoto walk you through exactly how to bleed SeaStar outboard hydraulic steering systems using our owncomprehensive bleeding kit. It’s easy to use and mess-free, great for both beginners and experienced boat owners.

Replacing the seals is an inevitable part of dealing with hydraulic steering systems in general, so it’s a handy skill to have. You’ll need to disassemble the steering system to replace the seals and then reassemble it again, but don’t let that scare you off! We have astep-by-step DIY videoto walk you through that process, too.

Need to bleed your system? Check out our variousSeaStar power steering bleeding solutions, including the comprehensive kit and individual parts so you can build your own.

What type of steering system do you have? While most sportfish crew would answer hydraulic, there are many variables today that differentiate the design, components and operation of a vessel’s steering system. Learning about your boat’s system can assist when it comes time for maintenance, ordering repair parts and performing bleeding (more about this later).

Most of these mechanical systems have gone the way of the dinosaur – replaced with a variety of hydraulic solutions on sportfish boats. Hydraulic systems provide better command of the vessel’s directional stability and result in less fatigue on the captain.

At its most basic level, a hydraulic steering system consists of a helm pump, steering cylinder, rudder(s) and interconnecting hoses. The helm pump is a hydraulic pump attached under the helm wheel.

When the helm wheel is turned, the helm pump pushes hydraulic oil through the hydraulic fluid lines and into the cylinder that pushes the internal piston one direction or the other, depending which way you turn the helm wheel. While most steering systems on sportfish boats are more complex with additional components, the operating principal is the same.

No matter what steering system your boat has, there are two common components to all systems: the hydraulic oil and cylinders. The most critical part of any hydraulic system is clean hydraulic oil. Many times, we hear about the need to bleed a steering system. The need is often caused by a leak in the system that let air or water into the system, while letting oil out.

A boat’s hydraulic steering is a closed system that operates on high pressures of 1000 PSI or more. At these pressures, even a slight leak from a hose or seal will quickly cause oil to leak out. This can possibly disable the steering system.

Each steering system manufacturer offers specific procedures for filling and bleeding of their systems. The basic premise for bleeding is to circulate clean hydraulic oil through the system while bleeding the air out until a steady stream of air and contaminant free oil is observed.

The most common power steering system uses an engine-driven hydraulic pump to provide high pressure hydraulic oil for the power circuit of the steering system.

A marine power steering system adds a second hydraulic cylinder and second hydraulic oil circuit from the engine-driven pump. The high-pressure power circuit is actuated by the manual system from the helm wheel.

This type of hydraulic steering operates similarly to the engine-driven power steering system, but without the engine driven pump. The hydraulic power comes from a standalone electric motor, usually supplied with DC power. These systems vary in design. While their primary application lies with large center console boats powered by multiple outboards, electric power steering pumps are becoming more popular in sportfish boats.

There are two design styles of electric power steering systems – one with a constantly running electric hydraulic pump and the other with an on-demand electric motor pump. While the end result is similar, the feel of the system and response time is slightly different.

Most of the large sportfish boats that use electric power steering include the constantly running engine, while the on-demand pumps system is often used in center console boats.

The constantly running pump system supplies high pressure hydraulic steering oil to the steering system continuously while the steering system is powered on. Contrarily, the demand system pump is always off, until the captain begins to turn the helm wheel, which triggers a sensor in the hydraulic system that turns on the pumps motor.

The on-demand system uses less electricity and helps reduce the steering effort as compared to manual steering, though the feel and reaction time is much different that and constant running pump.

In an EPS system, the helm wheel is connected to an electronic sensor instead of a hydraulic helm pump. Digital data signals are sent along wires to the steering system below deck, usually consisting of a computer processor, electric pump(s) and steering cylinder(s) that are connected to the rudders.

The most popular form of EPS is the Seastar Optimus system for outboards. This system consists of independent pumps and cylinders for each outboard engine. As you might imagine, a computer system controls the coordination of each outboard engine relative to the others. When the captain turns the helm wheel, the signals travel into the computer and then to each electric pump and engine cylinder.

Another feature of EPS systems is that the large hydraulic steering lines are replaced with small wires connected to each helm wheel. This makes adding a second or third steering station a much simpler task – as compared to routing bulky hydraulic lines. The new EPS systems are designed for both new construction and retrofit projects to replace traditional steering systems.

The Seastar Optimus EPS system is now also available for inboard boats up to 70’. The Optimus system operates in similar fashion as other electric inboard power steering systems, but is also available in more advanced configurations, depending on the application.

In its simplest form, the electronic power steering system uses an electronic helm, single power steering pump and single cylinder at the rudders. In a more advanced system, there can be one pump and cylinder for each rudder without a tie bar. This allows the rudders to operate independently or in unison, depending on the pre-programmed operating parameters.

Viking Yachts knew an EPS system like this would have many advantages for sportfish boats and designed their own system years ago. The steer-by-wire Viking Independent Proportional Electro-Hydraulic Rudder system is referred to as the VIPER steering system. The VIPER’s rudders are individually controlled with one steering cylinder per rudder. When the helm wheel is turned, an electric signal is sent to a controller whose software dictates the optimum position for each rudder.

No matter how advanced the system, steering still relies on traditional aspects such as rudder size and shape, properly sized hydraulic cylinders, helm pump, hoses and other components. A regular visual inspection of your steering system components will help you to learn what you have and determine if and when maintenance is needed.

Most autopilot manufacturers offer a system for boats with EPS systems. These autopilot systems are similar to a traditional autopilot system, except for one component – the hydraulic pump. In an EPS system, the autopilot manufacturers substitute a gateway or electronic module for the hydraulic pump. This gateway

Boats with traditional hydraulic steering use an autopilot system that incorporates a standalone autopilot hydraulic pump connected to the steering system as an additional station. There are a variety of hydraulic pumps available and are selected by capacity based on the volume of the steering cylinders. Don’t guess or select the pump by price as an undersized or oversized autopilot pump can cause unacceptable autopilot performance.

If your boat has a constant running power steering system, you may be able to forgo the need for the traditional autopilot pump. Some autopilots can connect to the existing directional solenoid valves in the power steering system.

A technical note – In regards to the hydraulic portion of the autopilot system the National Marine Electronics Association (NMEA) installation standard 0400, indicates that “Isolation valves shall be installed in the hydraulic lines connected to all ports entering the autopilot pump.”

This allows for isolation, service or replacement of the autopilot hydraulic pump without disturbing the rest of the vessel’s hydraulic steering system. This practice is often overlooked in many boat steering systems.