silent hydraulic pump in stock

> quiet series pumps for heavy duty continuous operation. > oil dely (cu. in./min): 730 @ 100 psi, 60 (60 series) & 120 (120 series) @ 10,000 psi. > enclosed 2 hp 230v motor (60 series) & 3 hp 460v motor (120 series). > * - models with S suffix include solenoid valve with 25" remote control.

Lalmek Hydraulics’ silent hydraulic pumps appear similar to a gear pump, but inside the difference is considerable. Thanks to a well thought out design of the pump’s rotating parts, it produces an even flow of oil. This in turn minimises vibration in the system and significantly reduces the noise level. It also lowers energy consumption while efficiency increases.

In axial piston fixed pumps, the flow is proportional to the drive speed and the displacement. Axial piston fixed pumps are available for hydrostatic drives in open circuit.

... control options provide the flexibility to match the pump to a wide range of pressing, punching and other operations. Compare the ZE2 to the other pumps in the ZE-Series and determine the best pump ...

... piston pump type V30D is designed for open circuits in industrial hydraulics and operate according to the swash plate principle. They are available with the option of a thru-shaft for operating additional ...

... adopted for conventional pumps. Accordingly, multiple pumps can be assembled using silent stages together with conventional stages, and silent pumps can also be equipped with all the ...

Gear pump with reversible Rotation direction and internal drainage. Built in aluminium body, lighter than casting pumps, permits to work at high pressures with a low level of noise.

Compact, Portable, Cordless Hydraulic Pump for MRO Applications. Compact, Li-ion 18VDC, 9.0 Ah battery-powered pump provides extended run-time. Two-stage, high-pressure ...

... Team 400 series offers both single or multiple cylinder applications. Two-speed high output pump delivers up to 5 gpm (16 liter/min) of oil, with a low noise level of 73-80 dBA. Integral ...

The Power Team 120 series pump is exactingly designed for heavy duty, extended cycle operation up to 400 Ton. Built in grit, the series 120 pump can start and operate under full load, even with voltage ...

Like all the pumps of the HP Series, it is suitable for any hydraulic application which require very high hydraulic output pressures and a moderate and controllable oil flow, to ensure ...

... HP-LEVER pump of the HP Series is a single-acting air-hydraulic pump with manual operation with an ergonomic lever. It has an oil flow rate of 2.4 to 0.1 l / min and operating pressures ...

Air hydraulic pump, double pneumatic motor, double effect, foot operated with lock-up function, lever distributor valve (4/3), 10L tank, oil flow 8.5 / 0.26 l / min

Gear pumps GP1K Group 1 is an Ideal solution for hydraulic power packs. Modern technologies and many years of experience of the HYDROSILA company allow us to create pumps with high reliability ...

... variable displacement pump DPVD impresses with its innovative technology. Thanks to the inverse piston, the pump manages large swing angles and can be used with nominal pressures up to 400 bar. The model ...

The best match of low-noise and high-efficiency! The helical shape of the patented Elika® profile eliminates the phenomenon of air encapsulation typical of normal gear pumps, curing the ...

... DIN is a series of in-line dual flow pumps with extremely low noise levels for demanding mobile hydraulics. SLPD 20/20-64/32 DIN comes in eight different sizes, where ...

1. High pressure fixed vane pump with high working efficency and can be applied in hydraulic circuits. ...

PGP 500 pumps offer superior performance, high efficiency and low noise operation at high operating pressures. They are produced in four frame sizes (PGP 502, PGP 505,PGP 511, PGP 517) ...

Gear pumps are used in a wide range of hydraulic systems; in fact, they are easily among the most common types of pumps seen in this type of equipment. Hydraulic gear pumps are of a fixed displacement design and operate by pumping fluid through a system by means of a prime mover such as an engine or motor.

Gear pumps are used in a wide range of hydraulic systems; in fact, they are easily among the most common types of pumps seen in this type of equipment. Hydraulic gear pumps are of a fixed displacement design and operate by pumping fluid through a system by means of a prime mover such as an engine or motor.

Although there are several uses for gear pumps and significant variations in gear pump components, their basic design and theory of operation is as follows. Every gear pump includes two (sometimes more) rotating gears whose teeth interlock. The rotation of the drive shaft turns the drive gear, which, due to the intermeshing design, also puts the other gear into motion. Hydraulic gear pumps do not create a strong suction so operate best with a flooded inlet.

Internal gear pumps – This types of pump utilises a “gear inside a gear” design. As the gears rotate in the same direction, the space between them varies in a controlled manner, resulting in displacement of the fluid. Internal gear pumps are noted for their relatively quiet operation and ability to manage thick fluid.

External gear pumps – These pumps have two intermeshed gears arranged side by side, one of which is connected to the drive shaft. Rotating the drive shaft creates motion in the gears and creates a flow path on the outside of each gear. An external gear pump can operate effectively at a variety of speeds and with a range of fluid viscosities. The main advantage is simplicity, size to power ratio, price to power ratio.

What can a hydraulic gear pump do that other pumps cannot? For the most part, hydraulic gear pumps offer precise output control that isn’t possible with centrifugal pumps, for example. Increasing or decreasing the speed of the prime mover will increase or decrease the output flow rate. Hydraulic gear pumps are normally made to only run in one rotation however this can normally be changed if required.

Hydraulic internal gear pumps are often more expensive than centrifugal pumps, whilst Hydraulic external gear pumps tend to be less expensive.. They tend to be noisier as well—which can be a problem in environments where extraneous noises cannot be tolerated—and cannot be used to handle abrasive materials.

White House Products Ltd carries high-quality equipment from today’s leading gear pump manufacturers. We invite you to explore the gear pumps that we have listed in this section.

With a simple but sophisticated design, we offer a gear pump that not only is quieter. It also has a unique advantage over the most popular low noise gear pump. The shhark® patented design guarantees the pump will remain silent after many hours of heavy-duty operation. This offers costs savings over traditional gear pump by eliminating costs associated with external noise reduction devices.

The shhark® design offers up to 10 dB noise reduction over regular gear pumps. It is ideal for application where low noise and high efficiency are required. Typical applications include tractors, indoor lift trucks, aerial platforms, construction equipment, material handling, agricultural and lifting devices.

The high pressure and large capacity pump with ample experience is combined with an electric motor by introducing a unique bellhousing. This development realizes compact pump units. Furthermore the flexible mount of the hydraulic pump alleviates the vibration and system noise.

By Kawasaki Silent System which realizes the best class of low noise characteristics in the industries of high pressure hydraulic deck machinery, it contributes to the improvement of living environment for passengers and crews on the vessel such as ferry.

The Silent 300 Prestige is a diesel-powered multi-purpose pump and spray machine with a built-in 6.3 cubic foot hydraulic mixer and onboard compressor for spraying. The military spec control panel integrates all these functions in one location to allow operators to quickly and easily learn to operate the pump. Known for its versatility, the Prestige is designed to use different rotor/stator combinations for pumping a variety of materials - including up to 3/8” aggregate.