skf hydraulic pump manufacturer

The 729124 pump is suitable for use with hydraulic nuts (smaller than or equal to HMV 54E) and for mounting and dismounting bearings or components where a maximum pressure of 100 MPa (14 500 psi) is required. The pump is supplied with 1 500 mm (59 in.) pressure hose, quick connect coupling and mating nipple and pressure gauge. The pump is filled with SKF Mounting fluid LHMF 300 and is supplied with an extra litre of fluid.

The 728619 E is a two-stage pump suitable for use with SKF Supergrip bolts and for the mounting and dismounting of bearings or components where a maximum pressure of 150 MPa (21 750 psi) is required. The pump is supplied with a 3 000 mm (118 in.) pressure hose, quick connect coupling and mating nipple and pressure gauge. The pump is filled with SKF Mounting fluid LHMF 300, is supplied with an extra litre and is protected in a sturdy metal case.

High-performance FlowMaster hydraulic pumps combine rotary-driven pump motors with reciprocating pump tubes and flexible control features that perform in desert heat and arctic cold. The integrated control manifold adjusts the amount of lubricant and operating pressure. The pump’s output is adjustable from 115 to 737 cm³/min (7 to 45 in³/min). FlowMaster pumps are optionally available incl.

The TMJL 100 pump is suitable for use with hydraulic nuts (smaller than or equal to HMV 92E) and for mounting and dismounting bearings or components where a maximum pressure of 100 MPa (14 500 psi) is required. The pump is supplied with 3 000 mm (118 in) pressure hose, quick connect coupling and mating nipple, and pressure gauge. The pump is filled with SKF Mounting fluid LHMF 300 and is supplied with an extra litre of fluid.

Pumps to supply this high pressure oil are typically complicated to assemble. However, the THHP 300 is ready to use with minimal preparation – allowing oil injection to be applied straight away, speeding up mounting and dismounting. Oil is automatically returned to the reservoir once pressure has been released, minimising the risk of leakage.

The pump can be used for mounting and dismounting such items as railway wheels and tyres, propellers and gears and similar type applications. For example, railway wheels are often heated and then mounted on a cylindrical shaft. After cooling the wheel has a tight fit on the shaft, without the need of having a key way. Later the wheel can be easily and quickly removed by using the SKF Oil Injection Method, by injecting oil at high pressure between the wheel and the shaft. The oil pressure breaks the interference fit and then greatly reduces friction. This simplifies the task of removing the wheel and helps to prevent shaft damage.

The TMJL 50 pump is mainly intended for use on the low pressure side of SKF OK couplings, but is also suitable for applications where a maximum pressure of 50 MPa (7 250 psi) is required. The pump is supplied with a 3 000 mm (118 in) long high pressure hose with quick connect coupling and mating nipple. It is filled with SKF Mounting fluid LHMF 300 and is supplied with an extra litre of fluid.

The 729124 pumpis suitable for use with hydraulic nuts (smaller than or equal to HMV 54E) and for mounting and dismounting bearings or components where a maximum pressure of 100 MPa (14,500 psi) is required. The pump is supplied with 1 500 mm (59 in) pressure hose, quick connect coupling and mating nipple and pressure gauge. The pump is filled with SKF mounting fluid LHMF 300 and is supplied with an extra litre of fluid. For applications where space does not permit the use of a quick connect coupling and nipple, such as AOH sleeves, a special pump design is available (729124 A).

The TMJL 100 pump is suitable for use with hydraulic nuts (smaller than or equal to HMV 92E) and for bearing install or removal or components where a maximum pressure of 100 MPa (14,500 psi) is required. The pump is supplied with 3000 mm (118 in) pressure hose, quick connect coupling and mating nipple, and pressure gauge. The pump is filled with SKF mounting fluid LHMF 300 and is supplied with an extra liter of fluid and has a greatly increased oil container capacity over the 729124 (800 cm3 - 48 in3).

The 728619 E is a two-stage pump suitable for use with SKF Supergrip bolts and for the mounting and dismounting of bearings or components where a maximum pressure of 150 MPa (21 750 psi) is required. The pump is supplied with a 3 000 mm (118 in.) pressure hose, quick connect coupling and mating nipple and pressure gauge. The pump is filled with SKF Mounting fluid LHMF 300, is supplied with an extra litre and is protected in a sturdy metal case.

Swedish pump manufacturer SKF has launched its BPH30 hydraulic barrel pump for large automatic lubrication systems used in demanding applications such as heavy machinery used in the construction and mining industries.

The BPH30 pump is available with or without sensors and can be configured to individual needs. It is designed for large automatic lubrication systems such as single-line, progressive or dual-line, as well as filling processes.

The BPH30 is constructed from heavy-duty materials, making it very robust. It also has a compact design, allowing it to be mounted in tight spaces, an operating temperature range from -40°C to +80°C and accepts greases up to NLGI 2. The pump has a single outlet, which can be positioned on the left, right or front of the device.

A special three-seal design helps to prevent leakage of both hydraulic oil and lubrication grease. This maintains safe and reliable operations, while minimising the risk of contamination. A leakage indicator provides clear visual confirmation that the sealing system is working.