stanley hydraulic pump parts brands

The TP03 and TP08 lines of trash pumps are a great example of the power of hydraulics when it comes to pumping liquids with solids. The TP03 pump provides 450 gallons per minute (1688 lpm) of discharge capacity and can pump solids up to 3 inch (76 mm) in diameter. The TP08 has a 800 gpm (3028 lpm) of discharge capacityand can pump up to 4 inch (102 mm) diameter solids.

A division of Stanley Black & Decker, STANLEY Infrastructure is the world’s largest handheld hydraulic tool manufacturer and a worldwide market leader, offering over 150 handheld hydraulic tools and over 30 mounted impact tools.

Stanley detwatering pumps, the pure power of hydraulic tools is also exemplified in our trash pumps. Our TP03 pump discharges an impressive 450 gallons per minute (1688 lpm) and can handle up to 3 inch (76 mm) diameter solids. Our TP08 discharges 800 gpm (3028 lpm) and can handle up to 4 inch (102 mm) solids.

The SM50 water pump is fitted with dripless flat-faced HTMA quick couplers for easy connecting and disconnecting of the pump and hydraulic system. The water outlet is a 3-inch pipe thread fitted with a 3-inch groove fitting to which can be connected a cam hose end fitting. Access to the pumping chamber for cleaning requires the removal of only two cap screws. The motor with the impeller attached is then easily removed from the pump casing. The SM50 can draw down water to a depth of 3.5 inches. Putting the SM50 in a sump will allow it to pump all but 3.5 inches of water remaining in the sump. The integral screen effectively keeps solids larger than 3/8 of an inch out of the pump. The pump will handle clear water and water containing up to 10% solids.

The SM50 Water Pump is a submersible, centrifugal type pump that requires no priming. The motor is contaminant-tolerant gear motor uniquely designed for continuous highspeed operation. The motor drives the impeller directly, so there are no spindle bearings that require periodic lubrication or replacement. The cast stainless steel, semi-closed impeller resists corrosion. A series of seals on the drive shaft effectively keep hydraulic fluid and pumped water where they belong while allowing the pump to be run dry without sudden seal failure. The SM50 is fitted with dripless flatfaced HTMA quick couplers for easy connecting and disconnecting of the pump and hydraulic system. The water outlet is 3-inch pipe thread fitted with a 3-inch groove fitting to which can be connected a cam hose end fitting. Access to the pumping chamber for cleaning requires the removal of only two capscrews. The motor with the impeller attached is then easily removed from the pump casing. The SM50 can draw down water to a depth of 3.5 inches. Putting the SM50 in a sump will allow it to pump all but 3.5 inches of water remaining in the sump. The integral screen effectively keeps solids larger than 3/8 of an inch out of the pump. The pump will handle clear water and water containing up to 10% solids.

The Stanley TP03 Trash Pump is the lightest, most efficient way to move large volumes of liquid with concentrations of solids up to 25% by volume. No priming necessary, just drop it into the material and it’s ready for work. The urethane bowl is virtually indestructible - tough, lightweight, abrasion resistant, resilient and impervious to petrochemical solvents. The TP03 can pump almost anything without damaging the bowl. The TP03’s efficient design places the urethane impeller above material flow, reducing blockage, jamming and overall pump wear while keeping liquids moving fast enough to pump high volumes of solids at a much higher head than non-submersible pumps. For easy maintenance and inspection, simply remove the wing nuts and top plate, clean out the bowl and replace the cover and nuts. You’re back to work in less than 5 minutes. The TP03 can run dry without damaging motor or impeller, reducing the possibility of downtime. It handles solids up to 3-inches at very high volumes to quickly and efficiently empty sumps, vaults, septic systems, trenches, etc.

When it comes to industrial tools, theres no better answer than Stanley industrial tool products. Whether it be pumps, hydraulic units or whatever else you could possibly need, Stanley Tools is the right choice, And JDC has you covered. JDC has made a commitment to suppling the best for our customers to aid in thier business efforts, and we don’t beleive in settling for anything less. Inquire about our available Stanely Tools industrial products today. Only available from selected locations.

“STANLEY Hydraulics has a proud tradition of being a global leader in the development of a wide range of innovative hydraulic products used in a variety of industries and applications. As a member of STANLEY Black & Decker Inc., a 165 year old company committed to the manufacture and distribution of quality tools for professional, industrial, and consumer, we at STANLEY Hydraulics Tools are dedicated to providing our customers with innovative customer-driven product designs, world-class performance, unmatched product support, and superior value”

The TP08 has a 100mm (4″) outlet and comes with a male Camlock fitting. Heavy-duty construction with a fabricated, all steel volute and abrasion resistant cast iron impeller. The volute uses replaceable wear plates to reduce wear and extend pump life.

The Stanley TP08 hydraulically driven trash pump can deliver 3028 lpm (800 gpm) and is ideal for dewatering, dredging, cleaning and as an effective bilge pump, it is commonly used in boat salvage, emptying of lakes, transfer of water and even for moving sand away from pipelines subsea.