vertical shaft hydraulic pump for sale

This 2-Stage pump fits a wide variety of log splitters and outdoor power equipment and works in both horizontal and vertical orientations. The included inlet nipple requires a 1" inner diameter suction hose.

Rated for up to 3,000 PSI at 3,600 RPM, this pump can power log splitters from 5 to 35 tons, depending on the inner diameter of the hydraulic cylinder. It features a fast cycle time by moving quickly when unloaded. It automatically shifts to low-flow/high-pressure mode at 500 PSI.

Be sure to use AW-32 10-Weight (ISO 32) or AW-46 20-Weight (ISO 46) light hydraulic fluid or Dexron III automatic transmission fluid. This pump is not designed for use with “universal” or "tractor" transmission oil, such as "303". The use of incorrect fluid may damage the pump and void the warranty.

Make sure the hydraulic fluid reservoir is not below the pump to ensure a sufficient flow of fluid to the pump. Suction-side filtration should be no finer than 150 microns. The use of a 10-25 micron filter on the suction side of the pump is too restrictive and will cause failure.

We recommend using an L-style jaw coupling to connect the pump to an engine. Couplings and mounting brackets are available. You should use at least a 5hp 163cc engine to maintain 3,600 RPM under load.

This 2-Stage pump fits a wide variety of log splitters and outdoor power equipment and works in both horizontal and vertical orientations. The inlet (suction) port is 1" NPT and the minimum suction hose inner diameter (ID) is 1-1/4". The inlet barbed fitting is not included but is available separately. Use a 1-1/4 ID Suction Hose and 3/4" ID high-pressure hose.

Rated for up to 3,000 PSI at 3,600 RPM, this pump can power log splitters from 5 to 37 tons, depending on the inner diameter of the hydraulic cylinder. It features a fast cycle time by moving quickly when unloaded.

Be sure to use AW-32 10-Weight (ISO 32) or AW-46 20-Weight (ISO 46) light hydraulic fluid. This pump is not designed for use with “universal” or "tractor" transmission oil, such as "303". The use of incorrect fluid may damage the pump and void the warranty.

Make sure the hydraulic fluid reservoir is not below the pump to ensure a sufficient flow of fluid to the pump. The hydraulic fluid reservoir should have a capacity of at least 12 gallons to allow sufficient cooling. Suction-side filtration should be no finer than 150 microns. The use of a 10-25 micron filter on the suction side of the pump is too restrictive and will cause failure.

We recommend using an L-style jaw coupling to connect the pump to an engine. Couplings and mounting brackets are available. You should use at least an 11.7hp 390cc engine to maintain 3,600 RPM under load.

17542 hydraulic pump shaft products are offered for sale by suppliers on Alibaba.comAbout 28% % of these are construction machinery parts, 12%% are hydraulic pumps, and 7%% are other hydraulic parts.

A wide variety of hydraulic pump shaft options are available to you, such as new, used.You can also choose from piston pump, gear pump and vane pump hydraulic pump shaft,as well as from 1 year, 6 months, and 1.5 years hydraulic pump shaft, and whether hydraulic pump shaft is hydraulic power units, fittings, or hydraulic motors.

I have seen it done and Swisher does make a splitter with a belt drive pump. The main problem I have been told from several people in the hydraulics business is that the pumps are not rated for an overhung load. The shaft is only 5/8" diameter and the bearings are not rated for the side load. I have not studied the Swisher units much so I cannot comment on their setup. They may use a differently spec"ed pump.

To do it right a jackshaft could be fabricated with a love joy coupling to connect the pump. The jackshaft would act as an overhung load adapter with the coupling at he end of the shaft to connect to the pump.

Hydraulic powered pumps for use in hydraulic drive and compatible power supply applications. The hydraulic pump uses a hydraulic motor to convert mechanical energy into pump output capacity that generates fluid flow. This is often in the form of a hydraulic oil hose and pump pressure system that is used to drive operation of the hydraulic pump. Hydraulic pumps come in centrifugal, transfer, roller and piston type pump models. They are engineered for customizable mounting and feature an individual motor and pump shaft that improves the ease of maintenance work. Pump types are designed for compatibility with a wide range of chemicals and applications. Hydraulic pumps are frequently used in commercial agriculture applications due to their improved power and performance. Hydraulic pumps are commonly used with tractors, sprayers and fluid transfer.

Available pumps are manufactured by ACE Pumps, Banjo, John Blue and Hypro brands. Banjo hydraulic pumps feature Gresen brand motors. Pump construction materials include cast iron, E-coated cast iron, aluminum, stainless steel, polypropylene, Ni-Resist and Silvercast. Pump seals are either Viton, EPDM or silicon carbide. Compatible max hydraulic flow rate for available hydraulic pumps range from 3 up to 24. The max flow capacity of hydraulic pumps ranges from 20 GPM up to 900 GPM. Maximum pressure output ranges from 58 PSI up to 300 PSI. Hydraulic pump inlet connections range from 1" up to 3" NPT, 220 up to 330 flange, and 5" ANSI flange sizes. Outlet connections range from 3/4" up to 3" NTP, 200 up to 300 flange, and 4" ANSI flange sizes. Operating parameters and specifications vary by pump model.

Engine pump adapters are used to connect a hydraulic pump to a gas engine while ensuring accurate shaft alignment and enclosing the coupling. Available at Northern Hydraulics, these bell housings allow for easy versatility of adapting your hydraulic pump to a gasoline or electric motor.

I gave this pump a 4 instead of 5 only because for the normal home owner wanting to install his/her own well pump the instructions are horrible or non existing! I would give this pump a solid 5 however because the quality, packaging, price was awesome! The shipping was pretty quick also. I wish I would have seen a spot to chat with an agent when I was trying to make the right selection although or a really good specs high light. Would be nice if you could at least put in information on what the well specs etc was and as a result of entering said information the computer kick back best choices.