vickers v20 hydraulic pump free sample

1 Eaton Vickers V1 V2 Vane Pump Vickers vane pump V1 V2 V21 22 Features V1 and V2 Series are fixed displacement and balanced type vane pumps. With compact sizes, they are available in single pumps and double pumps for both industrial and mobile application. The vane design with self compensation for wear and clearances makes volumetric efficiency of pump nearly constant over the service life. (the vanes always adjust its orbit to contact with the cam ring, even though wear occurs between the cam ring and vane tips) The vane pump is not damaged at low speed and high pressure operation because pumping action does not start until the speed is high enough for the vane to throw out. With hydraulically balanced design, the bearing is externally loaded only. Therefore, the pump requires minimized maintenance with long service life. The inlet or outlet ports can be rotated through increments of 9 o in relation to each other, providing application flexibility and easy installation. With optional flow control and priority valve covers, the pump can be used in more applications. The flow control cover can limit the flow to the primary circuit at the required flow rate, while diverts remaining flow to the tank. The priority valve cover maintains a constant flow to the primary circuit, while diverts remaining flow to the secondary circuit. Each cover comes with a relief valve to limits the maximum pressure of the primary circuit. Interchangeable with original Vickers pump of the same model. Handling For maximum service life, the pump should be protected from contamination. Filtering fluid before filling and during operation to maintain or exceed ISO cleanliness code 17/ 14. Replaceable elements should be changed as filter supplier instructions The drive shaft must align with the power source shaft. voiding shaft end thrust and applications that impose radial loading. The start-up procedures should be as follows: - Check the rotation of power source to match the rotation of pump. - Check inlet and outlet ports to assure all connections are properly installed and check all mounting bolts and flanges to assure all are tight and properly aligned. - Fill pump with fluid through the outlet port if the pump is mounted above the fluid level. The spline shaft models also need to be lubricated with an anti-fretting grease or similar lubricant. - Place all controls in the neutral position so the pump is unloaded during initial start-up. - Prime the pump within a few second when the pump is started. - leed off entrapped air from outlet circuit until a steady output flow is observed. The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change at any time without notice.

2 Ordering Code and Specifications Single Pump V2(F) - 1PS - 1C()-(H)-(L) Model V1, V2 Cover Omit - Standard Cover F - Flow Control Cover P - Priority Valve Cover Mounting 1-2-olt Flange Inlet Port Connection S Str. thd. (V1) Str. thd. (V2) P - 1. NPT (V1) NPT (V2) - 1. SP (V1) SP (V2) T Str. thd. (V1) Shaft Rotation (Viewed from shaft end) Omit - Turn right L - Turn left Pressurer Setting for Flow control and Priority Valve Cover bar (psi) - 17 (25) F - 13 (15) - 34 (5) G - 1 (175) C - 52 (75) H - 13 (2) D - 9 (1) J (225) E - (5) K - Flow rate Setting for Flow control and Priority Valve Cover L/min (USgpm) 2-7. (2) () (3) (7) (4) () (5) Outlet Port Connection V1 and V2 S Str. thd. (V1) Str. thd. (V2) P -.5 NPT (V1) -.75 NPT (V2) -.5 SP (V1) -.75 SP (V2) Delivery (USgpm at rpm) V1-1, 2, 3, 4, 5,, 7 V2 -, 7,, 9,,, 13 Outlet Port Position (Viewed from cover end) - Opposite inlet - 9 o CCW from inlet C - Inline with inlet D - 9 o CW from inlet Shaft 1 - Straight keyed 3 - Threaded with woodruff key - Woodruff key stub (V2 only) - Splined - Splined (V1 only) 15 - Splined (V2 only) 3 - Splined V1F, V1P, V2F, and V2P S Str. thd. for outlet and Str. thd. for tank port (V2F) P Str. thd. for outlet and.5 NPT for tank port (V1F and V2F) T Str. thd. for outlet and tank port (V1F) Str. thd. for primary outlet and tank port and Str. thd. for secondary outlet (V2P) K Str. thd. for primary outlet and tank port and.75-1 Str. thd. for secondary outlet (V1P) Model Series V1 V1F V1P V2 V2F V2P Ring Size Delivery at r/min & 7 bar USgpm Geometric Displacement cm 3 /r (in 3 /r) 3.3 (.2). (.4) 9. (.) 13.1 (.) 1.4 (1.) 19.5 (1.19) 22. (1.39) 19.5 (1.19) 22. (1.39) 2.5 (1.2) 29.7 (1.1) 3.4 (2.22) 39. (2.3) 42.4 (2.59) Delivery at 15 r/min & 7 bar L/min (USgpm) 4.7 (1.25) 9.4 (2.5) 14.2 (3.75) 1.9 (5.) 23. (.25) 2.4 (7.5) 33.1 (.75) 2.39 (7.5) 33. (.75) 37.5 (1.) (.25) 52.4 (13.75) 5.77 (15.) 1.5 (1.25) Maximum Pressure bar (psi) 152 (22) 13 (2) 152 (22) 152 (22) Maximum Speed rpm Minimum Speed rpm Weight kg (lb) (1-15) (1-1)

3 Installation Dimensions mm (inch) V1 Single Pump V1 Inlet Port 1.35"-UN-2 or 1"-NPT or 1"-SP SE O-ring boss connection DI 19.5/19.2 (DI.75/.749) 7.1 (3.) DI 2.5 (DI 3.25) DI 21.4 (DI.4) Outlet Port.75"-1UNF-2 or.5"-npt or.5"-sp SE O-ring boss Connection DI 4 (DI 1.1).7 (.5) 24. (.97) 44.4 (1.75) rpm &7bar 1, 2, 3 4, 5, 7 Dimension 5. (4.55) 7.3 (2.5) 1.9 (4.) 73.7 (2.9) 7. (5.) 7.7 (3.1) 13 (5.) 2.7 (2.47) Shaft 1 Keyd Shaft 4.75 (.17) SQ x 25.4 (1.) LONG KEY (1.5) DI 21.13/21. (DI.32/.27) DI 1.3 (DI 4.19).4 (.25) DI.1 (DI.44) 1 DI 95.2 (DI 3.75) V1F Tank Port.75"-1UN-2 or.5"-npt rpm &7bar 1, 2, 3 4, 5, 7 Dimension. (5.7) 4. (3.34) (5.32) 91.2 (3.59) 14.2 (5.52) 9.3 (3.79).7 (2.39) 1.9 (4.21) 31.7 (1.25) 24. (.97) 14.7 (.5) Outlet Port.75"-1UN (3.4) 51.5 (2.3) Shaft Splined Shaft 9 Teeth (.525) P.D. 3 Degree Press. ngle Pitch 1/32 Major Diameter 15.2/15. (.23/.22) Minor Diameter.2/. (.435/.4725) Flat Root Major Diameter Fit

4 Installation Dimensions mm (inch) Single Pump V1 V1P Secondary Outlet Port.75"-1UNF-2 SE O-Ring oss Connection rpm & 7 bar 1, 2, 3 4, 5, 7 Dimension 13. (5.) 4. (3.34) 13.4 (5.37) 91.2 (3.59) (5.57) 9.3 (3.79) 5.3 (1.9). (4.5) 24. (.97) 2. (.1) 31.7 (1.25) 17.9 (4.25) DI 19.1/1.93 (DI.745/.7452) 55. (2.19) 15.2 (.) Shaft 3 Splined Shaft Teeth 3 Degree Press. ngle Pitch 1/32 Major Diameter 15./15.2 (.25/.15) Flat Root 3.1 (1.19) 15.9 (.3) Tank Port For Pressure Relief of Primary Outlet Port.525"-1UNF-2 SE O-Ring oss Connection Primary Outlet Port.525"-1UNF-2 SE O-Ring oss Connection Other shaft options for V1 Series 3.17 (.5) 5 (1.97) 41.9 (1.5) 31.7 (1.25) 3.1 (1.19).5"-2UNF-2 DI 15./15.4 (DI.25/.24) DI 3.17 (DI.5) 17.72/17.4 (.9/.) 41.4 (1.3) 14.7 (.5) 13 Teeth-2.4 (.5) P.D. 3 Degree Press. ngle Pitch 1/32 Major Diameter 22.17/22.15 (.73/.72) Minor Diameter 1.3/1.35 (.7335/.7225) Flat Root Major Diameter Fit Shaft 3 Threaded with # Woodruff Key Shaft Splined Shaft 13 Teeth

5 Installation Dimensions mm (inch) V2 Single Pump V2 Outlet Port 1.25"-UN-2 or.75"-npt or.75"-sp SE O-ring boss connection Inlet Port 1.25"-UN-2 or 1.25"-NPT or 1.25"-SP SE O-ring boss connection 55. (2.19) 55. (2.19) DI 2.5 (DI 3.25) 凯利.7 (.5) 7. (2.) rpm &7bar 7,, 9, 13 Dimension 5.2 (4.93) 71.1 (2.) 131. (5.1) 77.5 (3.5) 13.7 (5.3) 2. (3.25) 14.2 (5.52).1 (3.39) 31 (1.22) Shaft 1 Keyed Shaft 4.7 (.1) SQ X 41.1 (1.2) LONG KEY 13 (5.) (2.) 2 (2.44) DI 21.13/21.3 (DI.32/.2) 1º 55. (2.19) DI 19.5/19.2 (DI.75/.749) DI 1.3 (DI 4.19) 4 (.1) DI.1 (DI.44) DI 95.2 (DI 3.75) Other shaft options for V2 Series 74. (2.94) 41.4 (1.3) 5. (2) 14.7 (.5) DI 19.7/19.2 (DI.751/.749) 37.3 (1.47) Full Depth of Spline DI 19.1/1.93 (DI.749/.745) Teeth 3 Degree Press. ngle Pitch 1/32 Flat Root 13 Teeth-2.4 (.5) P.D. 3 Degree Press. ngle Pitch 1/32 Major Diameter 22.17/22.15 (.73/.72) Minor Diameter 1.3/1.35 (.7335/.7225) Flat Root Major Diameter Fit Shaft Splined Shaft Teeth Shaft 15 Splined Shaft 13 Teeth

6 Installation Dimensions mm (inch) Single Pump V2 V2F and V2P Secondary Outlet Port.75-14UNF-2 SE O-Ring oss Connection Tank Port 1.25-UN-2 or.5"-npt rpm & 7 bar 7,, 9, 13 Dimension 149. (5.9) 94.7 (3.73) 15. (.14) 11.1 (3.9) 11. (.34) 15.9 (4.17) 14.3 (.47) 19.5 (4.31) 55. (2.19) 55. (2.19) 31. (1.25) 31 (1.22) 19.1 (.75) 4 (4.) DI 19.1/1.93 (DI.749/.745) 2 (2.44) 4 (.1) Shaft 3 Splined Shaft Teeth 3 Degree Press. ngle Pitch 1/32 Flat Root 15. (.2) 15. (.2) Tank Port For Pressure Relief of Primary Outlet Port.75"-1UNF-2 SE O-Ring oss Connection Primary Outlet Port.75"-1UNF-2 SE O-Ring oss Connection Outlet Port SE O-Ring oss Connection V2P V2F Other shaft options for V2 Series 31. (1.25) 7. (2.7).7 (.5) 2.9 (1.) 31. (1.25) DI 19.1/1.93 (DI.749/.745) 1.3 (.72) 1. (.) 2./25.2 (1.27/1.17).7 (.5) DI 2.9 (DI 1.) DI 23.3/23.1 (DI.93/.9375) 1.25" HEX.75"-1 THD. Shaft Straight Stub Keyed Shaft Shaft 3 Threaded with # Woodruff Key

7 Ordering Code Double Pump V21(F) - 1F13S7S - 1CC-()(H)-(L) Model V21, V22 Cover Omit - Standard Cover F - Flow Control Cover P - Priority Valve Cover Mounting 1-2-olt Flange Inlet Port Connection F - 4-bolt Flange Dia 1.5 (V21) - 4-bolt Flange Dia 2. (V22) Shaft End Pump Delivery (USgpm at rpm) 7,, 9,,, 13 Shaft End Outlet Port Connection S Str. thd. P -.75 NPT -.75 SP Cover End Pump Delivery (USgpm at rpm) V21-1, 2, 3, 4, 5,, 7 V22 -, 7,, 9, Cover End Outlet Port Connection V21 and V22 S Str. thd. (V21) Str. thd. (V22) P -.5 NPT (V21) -.75 NPT (V22) -.5 SP (V21) -.75 SP (V22) Shaft Rotation (Viewed from shaft end) Omit - Turn right L - Turn left Pressurer Setting for Flow control and Priority Valve Cover bar (psi) - 17 (25) F - 13 (15) - 34 (5) G - 1 (175) C - 52 (75) H - 13 (2) D - 9 (1) J (225) E - (5) K - Flow rate Setting for Flow control and Priority Valve Cover L/min (USgpm) 2-7. (2) () (3) (7) (4) () (5) Cover End Outlet port position (Viewed from cover end) V 21, V21F, V21P o CCW from inlet - 45 o CCW from inlet C - 45 o CW from inlet D o CW from inlet V22, V22F, V22P - Opposite inlet - 9 o CCW from inlet C - Inline with inlet D - 9 o CW from inlet Shaft End Outlet Port Position (Viewed from cover end) - Opposite inlet - 9 o CCW from inlet C - Inline with inlet D - 9 o CW from inlet Shaft 1 - Straight keyed - Splined V21F, V21P, V22F, and V22P S Str. thd. for outlet and Str. thd. for tank port (V22F) P Str. thd. for outlet and.5 NPT for tank port (V21F and V22F) T Str. thd. for outlet and tank port (V21F and V22F) Str. thd. for main outlet and tank port and Str. thd. for secondary outlet (V22P) K Str. thd. for main outlet and tank port and.75-1 Str. thd. for secondary outlet (V21P)

8 Specifications Double Pump Model Series V21 V22 Cartridge Position Shaft End Cover End Shaft End Cover End Ring Size Delivery at r/min & 7 bar USgpm Geometric Displacement cm 3 /r (in 3 /r) 22. (1.39) 2.5 (1.2) 29.7 (1.1) 3.4 (2.22) 39. (2.3) 42.4 (2.59) 3.3 (.2). (.4) 9. (.) 13.1 (.) 1.4 (1.) 19.5 (1.19) 22. (1.39) 22. (1.39) 2.5 (1.2) 29.7 (1.1) 3.4 (2.22) 39. (2.3) 42.4 (2.59) 19.5 (1.19) 22. (1.39) 2.5 (1.2) 29.7 (1.1) 3.4 (2.22) Delivery at 15 r/min & 7 bar L/min (USgpm) 33. (.75) 37.5 (1.) (.25) 52.4 (13.75) 5.77 (15.) 1.5 (1.25) 4.7 (1.25) 9.4 (2.5) 14.2 (3.75) 1.9 (5.) 23. (.25) 2.4 (7.5) 33.1 (.75) 33. (.75) 37.5 (1.) (.25) 52.4 (13.75) 5.77 (15.) 1.5 (1.25) 2.39 (7.5) 33. (.75) 37.5 (1.) (.25) 52.4 (13.75) Maximum Pressure bar (psi) 152 (22) 152 (22) 152 (22) 13 (2) 152 (22) 152 (22) Maximum Speed Weight rpm kg (lb) (3) (35) 25

9 Installation Dimensions mm (inch) Double Pump V (1.41).5"-13UNC (.) Deep Shaft End Outlet Port 1.25"-UN-2 or.75"-npt or.75"-sp Cover End Outlet Port.75"-1UNF-2 or.5"-npt or.5"-sp (2.75) DI 11. (DI 4.) 55. (2.19) Inlet Port DI 3.1 (DI 1.5).7 (.5) 1.2 (4.3).5 (2.3) 7.2 (3.) 5. (2.) 5.7 (2.31) C 2.9 (1.) Shaft 1 Keyed Shaft 4.75 (1.7) SQ x 31. (1.25) LONG KEY.5 (2.2) DI 22.23/22.2 (DI.75/.74) 174. (.) DI 14 (DI 5.75) (.37) DI 24.54/24.41 (DI.9/.91) DI 14.2 (DI.5) DI 1 (DI 4.75) rpm & 7 bar Dimension Shaft End Cover End C 7,, 9 7,, 9 7,, 9, 13, 13, 13 1, 2, 3 4, 5, 7 1, 2, 3 4, 5, 7 1, 2, 3 4, 5, (.39) (.4) (.4) 21.2 (.59) (.4) 229. (9.4) (.73) 227. (.97) (9.17) 75.9 (2.99) 2.3 (3.24) 7.4 (3.44) 75.9 (2.99) 2.3 (3.24) 7.4 (3.44) 75.9 (2.99) 2.3 (3.24) 7.4 (3.44).4 (3.4).4 (3.4).4 (3.4) 91.2 (3.59) 91.2 (3.59) 91.2 (3.59) 94.7 (3.73) 94.7 (3.73) 94.7 (3.73) Other shaft options for Double Pump V21 and V (1.2) (1.3) 3.9 (.15) DI 17. (DI.73) DI 29.2 (DI 1.15) 13 Teeth - 3 Deg Pressure ngle Pit ch 1/ 32 Major Diameter 22.17/22.15 (.73/.72) Form Diameter 19.3 (.749) Minor Diameter 1.3/1.35 (.734/.723) Major Diameter Fit Shaft Splined Shaft

10 Installation Dimensions mm (inch) Double Pump V22.5"-13UNC (.94) Deep 42. (1.9) Shaft End Outlet Port 1.25"-UN-2 or.75"-ntp or.75"-sp 5. (2.) 5. (2.) 74.7 (2.94) 77. (3.) DI 11. (DI 4.) 55. (2.19) Cover End Outlet Port 1.25"-UN-2 or.75"-ntp or.75"-sp Inlet port DI 5. (DI 2.).7 (.5) 1.2 (4.3) C 5.7 (2.31) 2.9 (1.) 174. (.) 9. (2.75) Shaft 1 Keyed Shaft 4.75 (1.7) SQ x 31. (1.25) LONG KEY.5 (2.2) 5. (2.) DI 22.23/22.2 (DI.75/.74) DI 14 (DI 5.75) (.37) DI 24.54/24.41 (DI.9/.91) DI 1 (DI 4.75) DI 14.2 (DI.5) rpm & 7 bar Dimension Shaft End Cover End C 7,, (.41) 73.7 (2.9) 7.1 (3.43) 7,, 9 7,, (.). (3.15) 7.1 (3.43), 13, 13, 13 7,, 9 7,, (.1) 225. (.) (9.5) (.75) 22.3 (.99) (9.19) 73.7 (2.9). (3.15) 5.1 (3.35) 73.7 (2.9). (3.15) 5.1 (3.35) 92.2 (3.3) 92.2 (3.3) 92.2 (3.3) 95.5 (3.7) 95.5 (3.7) 95.5 (3.7)

11 Performance Characteristics V1, Cover End of V21 ased on viscosity 32 cst (15 SSU) oil at 49 o C ( o F) and pump inlet at PSIG (14.7 PSI).1. 7 gpm 7 bar( 1 psi) 9 bar (1 psi) 13 bar (2 psi) gpm-13 bar (2 psi) gpm-172 bar 2 (25 psi) De livery-l/m in De livery-l/m in De live ry-l/min gpm 9 bar (1 psi) 172 bar (25 psi) Spee d-rpm 152 bar (22 psi) gpm bar (1 ps i) bar (25 psi) gpm 4 9 bar (1 psi) 172 bar (25 psi) gpm 14 9 bar (1 ps i) 172 bar (25 psi) USgpm USgpm USgpm Input-k W Input-kW Input-kW gpm 7 bar ( 1 ps i) 9 bar (1 ps i) 172 bar (25 psi) gpm-9 bar 14 4 gpm-9 bar 7 gpm-7 bar (1 ps i) 4 gpm-7 bar (25 psi) 1 gpm-9 bar 1 gpm-7 bar gpm-172 bar (25 psi) 5gpm-9 bar (25 psi) 2 gpm-9 bar gpm-7 bar 2 gpm-7 bar gpm gpm-152 bar 24 (22psi) 3 gpm-172 bar 2 (25psi) 1 gpm-9 bar (1psi) 3 gpm-9 bar 3 gpm-7 bar hp hp hp Spe ed-rpm For the Cover End Cartridge, the speed could not exceed the maximum speed of the Shaft End Cartridge.

12 Performance Characteristics V2, Shaft End of V2**, Cover End of V22 ased on viscosity 32 cst (15 SSU) oil at 49 o C ( o F) and pump inlet at PSIG (14.7 PSI) gpm gpm-152 bar (22 psi) 4 9 bar (1 psi) bar (22 psi) gpm- 172 bar (25 psi) bar (1 psi) 172 bar (25 psi) gpm- 172 bar 3 De live ry-l/m in De live ry-l/m in De live ry-l/m in bar (1 psi) bar (25 psi) g pm 9 bar (1 psi) 152 bar (22 psi) gpm 9bar (1 psi) 172 bar (25 psi) USgpm USgpm USgpm Input-k W Input-kW Input-kW gpm-9 bar 9 gpm- 9 bar gpm- 9 bar gpm-7 bar gpm- 7 bar gpm- 7 bar gpm 9 bar (1 psi) bar (25 psi) gpm-172 bar (25 psi) gpm- 172 bar 35 (25 psi) 3. 7 gpm gpm-9 bar 2 9 bar (1 psi) gpm- 9 bar 172 bar (25 psi) gpm-7 bar Spee d-rpm gpm- 7 bar Spee d-rpm gpm-7 bar 4 gpm-152 bar (22 psi) 35 gpm- 172 bar (25 psi) 3 gpm-9 bar gpm- 9 bar gpm- 7 bar hp hp hp For the Cover End Cartridge, the speed could not exceed the maximum speed of the Shaft End Cartridge.

13 Parts information Victory Pump Manufacturing Vickers vane pump V22P1FS7TC3H217 V2F1SSGL V1154R V11C2L V22P1F9STC3H217 V21P1P1C V2F1P13P3C22L V211F1371DD1 V2E7S2 V11P2S224 V2F1S7S3CK22L V1142 V21S7R V11P2S224 V11549 V114C2 V1F15T3C3F2L V21P7P15C V1154L9 F3V11R F3V11SS V21S7S1 V2F1S9S3C7K22L V211F711 F3V2F1P13P3CH22L V21PS1D V211F2CC V1172 V2F1PPCG22L V21PP1C V2F1SP3G22 V1172 V211F3CC V21P7P1 V21SM13SM1C V117C2 V2F1PP3C1G22 V21P7P1C V2F1SSCF22 V22P1FS7TC3H2 V2F1PP3CE22 V21S1S23C V111C2L V11332 V2F1PP3DH22 V21P7S1 V211F4CC V1133C2L V2F1PP3CE22 F3V11P2P1C2 V1143C2 V1P1S7K175 V2F1PP3DK22 V21ES23 V211F11CC V21F1F13TCFL V2F1PP35G22L V2F1PP3C1G V211F71 V21F1F13TCCF V2F1PP35J22L V21SS1 V211F71CC V211F721 V2F1PP3CE22L V21SS1CL V221F13 V211F721 V2F1PP3CE22 V2F1PP3CD V211F74 V211F721C V2F1PP3CH22 F3V11P5P1C2 V211F135CC V211F721CC V2F1PP1DH22L V21S13S23C F3V211F731 V211F73 V2F1PP23C1F22L V21S9S23C V2F1PP3J22 V211F751 V2F1PP3CH22 V21PP3CL F3V1142 V211F751CC V2F1SS1CH22 V21E9S23 F3V221F713 V211F21 V2F1SSG22L V21E9S23C V211F7P4P1 V211F21CC V2F1SSDG22L V2F1SPGL V211FP5P1 V211F31 V2F1SSCH22 F3V21PS1 V2P1PT1C2FL V211F31L V2F1SS3CK22 F3V21P13P1C V1173C2 V211F31CC V2F1S13S31G22L V21P9P3CL V2F1SS1CD22 V211F41 V2F1S13S31G22 V1F1P5PC2 V2151C V211F41 V2F1S13S31G22L V1F1P7P3D5H2 V211FP2P1CC V211F41L V2F1SPG22 V1P1SK3D1H1 V1FS3TF2 V211F41CC V2F1SPG22L V1F1P4PC3F2 F3V211F31 V211F51 V2F1SS3C7H22L V21E13K23C V21P9P1 V211F51L

Successfully sold in this country for the last 20 years because it is fully interchangeable with Eaton, Vickers, Cessna type V10 type Vane Pumps. Designed for low to medium pressure applications (up to 2500 PSI, 175 bar) Vane pumps offer a quieter, more flexible, and re-buildable alternative to the traditional gear pump.

Take a look at the videos below to see and hear about the individual parts and their availability for the V10 Vane Pump, and to see an explanation of why the "balanced" design of the V10 vane pump is far superior and a great alternative or as a replacement to the gear pump.

Hydraulic. online have worked together with one of Australia"s largest and most reliable importers to bring you Quality Reliable V10 Type Vane pumps at great prices. Try one for 30 days and if you are not completely satisfied return it to us for a full refund.

Unlike gear pumps the V10 Vane Pump pressure cartridge is internally balanced this means that there are no internal radial loads applied to the shaft and bearings even under higher pressures because of this balanced design V10 type Vane pumps generally have a much longer service life.