kelly hose failure quotation

Drilling hose also called Oilfield drilling hose, rotary drilling hose, is hollow, thin-walled, steel or aluminium alloy piping that is used on drilling rigs. It is hollow to allow drilling fluid to be pumped down the hole through the bit and back up the annul-us. It comes in a variety of sizes, strengths, and wall thicknesses, but is typically 27 to 32 feet in length (Range 2). Longer lengths, up to 45 feet, exist (Range 3).

Oilfield drilling hoses have found their wide application in the extraction of minerals such as oil & gas drilling. With the help of the drill pipe, a drilling mud is injected into the well at a very high pressure, most often technical water, hydrogel solution or clay-based solutions. The drill hose is also used between oil tankers and drilling wells in the sea. Drilling hoses can be used on stationary and mobile drilling rigs, for drilling wells in the sea.

The drilling rotary hose is suitable for flexible connection between the top of the drilling riser and the swivel which can move vertically. It resists corrosion of hydrogen sulfide and can deliver water, oil, mud high‐pressure media.

Rotary drilling hose is mainly used for conveying water-based or oil-based mud and other fluids in the working temperature of -30 °C to +82 °C. It is often used for oil fields, cement repairing, geological exploration and water conveyance for coal excavation. It is composed of three parts: tube, reinforcement and cover. The tube is made from NBR, which is resistant to abrasion, corrosion and oils. The reinforcement is made from 2-8 layers of high tensile and high strength spiraled steel wire, making the hose have solid structure and resistant to high pressure. The cover is made from high quality synthetic rubber, mainly chloroprene rubber, making the hose resistant to abrasion, corrosion, cut, weather, ozone, aging and sunlight. The hose has longer service life as a result.

Cover: high quality synthetic rubber, mainly chloroprene rubber, making the hose resistant to abrasion, corrosion, cut, weather, ozone, aging and sunlight.

As drilling operation methods evolve, become deeper, with increasing pressure and higher temperatures, JYM can provide a range of drilling and cementing hose solutions to meet these challenging conditions.  Our key offering includes rotary drilling / vibrator hose grade D and E, choke and kill, cement and sour hoses.  The JYM range supports the pumping of mud at very high pressure during drilling and exploration campaigns.

JINYUAN RUBBER CO., LTD. has been an important partner of many famous customers including America, East Asia, Africa and other countries and regions in the world. Oilfield drilling hoses are vital components for rig drilling systems. Rotary drilling hose, mud hose, cement hose, Kelly hose, vibrator hose are working under high-pressure. Once the hose failure, it will cause catastrophic damage to the equipment, body health and property. Our professional engineers can help you solve any problem in safe storage, handling and other technical problems. Our drilling hoses are equipped with API end fittings – flanges, NPT threads and butt-weld unions to meet requirements on the market. Bespoke end fittings are also available. Hose quality is our life. It is our aim to provide constantly high level of quality. All production processes and procedures have been strictly inspected. The final inspection before shipment is the strictest and any inferior products are not allowed in our company. When you purchase our products, we will provide considerable after-sales service. If the drill rotary hoses fail in warranty time, they can be returned without costing you one cent of shipment.

A large-diameter (3- to 5-in inside diameter), high-pressure flexible line used to connect the standpipe to the swivel. This flexible piping arrangement permits the kelly (and, in turn, the drillstring and bit) to be raised or lowered while drilling fluid is pumped through the drillstring. The simultaneous lowering of the drillstring while pumping fluid is critical to the drilling operation.

Manufacturing: Whip Checks, Nylon Hose Chokers, Cable Hose Chokers, Whip Stops, Piping Hobbles, Red Iron Chokers, Red Iron Slings, Cable Choker Hose Restraint, Hose Pipe Hobble Clamps, Hose Hobbles, Safety Shackles, Oilfield Hose Pipe Restraints, 1502 Piping Restraints, Frac Iron Safety Restraints, Rotary Hose Clamps, Pipe Safety Clamps, Flow Back Pipe Restraints, Four Bolt Pipe Clamps, Drilling Rig Fabrication, Oil Field Piping

Recognized as one of the most efficient high pressure hose safety restraints, the Whip Socks are designed to prevent injuries and severe fatalities in the event of a hose failure. Whip Sock’s name is inspired by the structure, the stocking style Hose Whip Stops device sits around a hose similar to a woven steel sock. The idea is to provide a grip on a hose over the larger area so to securing the hose and prevent it from whipping if a high-pressure accident causes the hose to release from its place.

There are several varieties of equipment to stop a hose from whipping around in case of unpredictable whipping hose accidents. Not only do the braided cable restraintshelp to protect the pipe from potential rapture, it also prevents the hose from whipping around.

Our Whip socks are used not only as air hose safety equipment but for other hose carrying agents as well. They can be incorporated in hose safety systems for a variety of applications where different substances are transferred through a hose at high-pressure, including; air, fluid, water, hydraulic, slurry, mud etc.

The whip sock is made for safety as its primary function. It features a unique construction that prevents unpredictable and potentially hazardous movement of a high pressure hose in the event of failure. Hence, the whip stop is ideal for any workplaces where personnel are in close working range with high pressure hoses.

The Raah Safety WHIP STOP is made from braided steel cable that wraps over the small pipe or hoses. The design is made in such a way that in case of pressure force is applied from the interior, the cable to tighten down on the hose, hence controlling the hose lashing.

The Make sure the Whip Stop has a good fit on the hose, lay it nice and flat. Once put on the hose make sure the netting diamonds are as wide as they are longer to create a nice tight fit. Once installed brace the hose and pull on the Whip Stop, it should not slide, if it slides it’s too big, you need to replace to the correct size Whip Stop. Regular inspection of the Whip Stop is advised once installed. Make sure the eyes are not elongated or ruptured or have any broken wires; Always lookout for rust on the Whip Sock or any individual strands broken. This means the whip stop has been under a load and needs to be pull out of service and replaced with a new Whip Stop.

The force calculator will give you the forces created during a failure with fluid.To calculate the force on hoses with air or gases, double the fluid reading.

Raah Safety supplies high pressure hose restraint systems, including; Whip Stops, hobble claims, whip checks, red iron sling and more. Contact us to find out more about the suitable hose restraint systems for your exact demands, or get customized tagging or pressure ratings. Place an order today and take advantage of our exceptional discounts on bulk purchases.

Steel wire braided hydraulic hose(one or two steel wire braided )SAE 100R1AT/DIN EN853 1SNSAE 100R2AT/DIN EN853 2SNDIN-EN857 1SCDIN-EN857 2SCSAE 100R1A/DIN EN853 1STSAE 100R1A/DIN EN853 2ST

SAE 100R5SAE 100R16SAE 100R17Pressure washer hoseMulti spiral hydraulic hose (four or six high tensile steel wire spiralDIN EN856 4SPSAE 100R9SAE 100R12DIN EN856 4SHSAE 100R13SAE 100R15Textile Braid Hydraulic HoseSAE 100R3SAE 100R6

Parker"s Series 7234 Wildcatter Oilfield Slim Hole Rotary Drill Hose is compatible with many oilfield media and provides excellent high pressure service across multiple drill site applications. The hose incorporates high pressure and high temperature capabilities and features a cover that is resistant to abrasion, oil and weathering to provide maximum performance. Series 7234 is qualified with permanent crimp couplings for a safe and secure connection and provides robust service life in challenging applications.

• Couplings attached with bands or clamps may reduce the working pressure of the hose assembly to less than the maximum rated working pressure of the hose. Refer to NAHAD Industrial Hose Assembly Guidelines

2. Set the drillpipe slips, break out the kelly and set the kelly back in the rat-hole (another hole in the rig floor which stores the kelly and swivel when not in use)

Though a failing coolant hose in your car might not be a life-threatening problem, it is one that can greatly affect your car over time. If you notice that your engine is overheating, this could point to a failing coolant hose.

Overheating in your car can cause engine damage and even a full engine rebuild. In order to avoid this costly consequence, bring your car to Huron Automotive in Green Bay, WI. At Huron Automotive, we can help you find and fix your failing coolant hose before it takes a toll on your engine.

The purpose of a coolant hose is as straightforward as it sounds. A coolant hose is a long radiator hose that sends coolant from your engine and your radiator to other parts of your car. It often sends coolant to the water pump and is responsible for keeping your engine from working too hard and overheating.

Your coolant hose is one of the most important parts of your vehicle. Without the coolant hose, your engine will no longer be able to run as designed and risks overheating.

One of the most important things to know is when to replace your coolant hose. It is important not to wait until noticing performance problems before opting to replace your vehicle’s coolant hose. The best thing to do is look for signs that your coolant hose is malfunctioning. Watch for these signs:

You can see a separated hose under your car hood.If you open your car hood to look inside and at any point see a disconnected tube or hose, this could mean that your coolant hose is no longer properly attaching where it needs to be. Take your car to Huron Automotive where we will replace your hose for you.

Your engine is burning or overheating.A burning smell or engine thermometer reading that shows your vehicle overheating could be a sign that your coolant is not flowing properly through your car. Replacing your coolant hose can be an easy fix to an otherwise hazardous problem.

You notice a leak under your car.If you notice a clear watery leak on the ground underneath your engine, this could mean that your coolant hose has sprung a leak. Leaking coolant will drip on the ground and form a puddle when your car is not in motion.

There are a few different reasons for why your car’s coolant hose might fail, leaving you with a leak, burning smell, check engine light, or overheating engine. Some of these reasons might include:

Your coolant hose is old.If your coolant hose is too old, it could become cracked and damaged or disconnect easily. In order to avoid a broken coolant hose, make sure to take your car to the repair shop for routine inspections where professionals can replace your coolant hose before it becomes too brittle.

Your coolant hose has a leak.If your coolant hose has a leak, it will fail to transfer coolant from the radiator or engine towards the water pump. This creates damage for the rest of your vehicle.

Your coolant hose is not attached properly.A bad attachment can put too much stress on your coolant hose, causing it not to work properly. Bring your car to Huron Automotive where we can fix your coolant hose attachment.

No matter what car you drive, at Huron Automotive in Green Bay, WI, we offer over twelve different services with a smile. With two convenient locations and rotating coupon deals for your satisfaction, we can easily diagnose and repair your car’s failing coolant hose to keep you and your family safe on the road. Call us today for an appointment.